Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
Time and temperature decrease (22) and increase (25)
Press this icon to decrease (22) or increase (25) the cooking time or temperature. Make sure
you have previously pressed the icon 19 to modify the parameters; otherwise, the device will
not modify the values.
4. CLEANING AND MAINTENANCE
-
Disconnect the appliance from the power supply and allow it to cool down before cleaning.
-
Always clean the appliance after each use.
-
Allow the device and accessories to cool down before disassembling and cleaning it.
Cleaning the exterior housing and the door
-
Do not use metallic tools or abrasive products to clean the device exterior. Use a soft,
damp cloth to clean the device surface.
-
Never immerse the appliance in water or other liquid.
-
Do not use sponges, powder products or abrasive cleaning agents to clean the product.
-
Use a damp sponge to clean the product surface. You can use a non-abrasive liquid
detergent or a mild spray solution to prevent stains from building up. Apply the cleaning
product to the sponge and not to the device surface directly.
-
To clean the glass door, use a glass cleaner or mild detergent and a damp sponge or soft
plastic scouring pad. Do not use abrasive products or metallic scouring pads, as they may
scratch the surface of the device.
-
Clean the control panel with a soft and damp cloth. Apply the cleaning product to the cloth,
do not apply it directly to the control panel. Cleaning the control panel with a scouring pad
or abrasive products may scratch it.
Interior cleaning
To clean any splashes that may occur during cooking processes, use a soft, damp sponge to
wipe the walls. You can use a non-abrasive liquid detergent or a mild spray solution to prevent
stains from building up. Apply the cleaning product to the sponge and not the inside directly.
Warning
Extreme caution when cleaning the resistor to avoid damaging it. Allow the device to cool down
completely and then carefully wipe it with a soft, damp sponge or cloth along the resistors. Do
not use any type of cleaning product or detergent. Allow all surfaces to dry thoroughly before
connecting the power cord to the power outlet and turning on the device.
Cleaning the crumb tray
-
After every use, remove the crumb tray and dispose of the crumbs. Use a damp sponge
to clean the tray. You can use a non-abrasive liquid detergent or a mild spray solution to
52
BAKE&FRY 3000 STEEL TOUCH
prevent stains from building up. Apply the cleaning product to the sponge and not to the
tray directly. Dry it properly.
-
To get rid of fat, soak the tray in soapy water and wash it with a sponge or soft plastic
scouring pad. Rinse and dry thoroughly.
-
Always make sure to insert the fat-drip tray back into the device after cleaning and before
connecting the power cord to the mains socket or turning on the device.
Accessories cleaning
-
Wash all accessories in warm soapy water and use a sponge or a soft plastic scouring pad.
Rinse and dry thoroughly.
-
Do not use abrasive cleaners, scouring pads or metal utensils to clean any of the
accessories, as this may damage the surface.
-
Accessories are not dishwasher safe.
Storage
-
Make sure all its parts are clean and dry when you store it.
-
Make sure the door is closed.
-
Store the device cool, on a horizontal surface and on the support feet. Do not store it while
it is hot or wet. Do not store it in hot and humid environments.
5. TROUBLESHOOTING
Error code
Problem
E1
Temperature sensor. Open
circuit.
E2
Temperature sensor.
Overheating or short circuit.
ENGLISH
Solution
In the last 2 minutes after the
cooking process starts, the device
will beep 10 times.
Turn off the device and turn it on
again.
If the problem persists, contact the
official Technical Support Service of
Cecotec to repair it.
5 seconds after starting the cooking
process, the device will beep 10
times. Turn off the device and turn it
on again.
If the problem persists, contact the
official Technical Support Service of
Cecotec to repair it.
BAKE&FRY 3000 STEEL TOUCH
53
Publicidad
