Descargar Imprimir esta página

Pentair OMNIFILTER OM26KCS Instrucciones De Instalación página 22

Publicidad

Idiomas disponibles

Idiomas disponibles

PERFORMANCE DATA SHEET
Model
Maximum Rated Service
Flow (gpm) (W/upper
collector)
Pressure Drop at Rated
Service Flow Rate (gpm)
Rated Capacity
(grains @ lbs of salt)
Rated Efficiency
(grains/lb Salt @ lbs of
salt)
Maximum Flow Rate
During Regeneration (gpm)
Resin Volume per tank - ft
3
ResinType - Strong Acid
cation
Tank size
Operating Pressure: 20 -125 psi or 1.4 – 8.8 kg/Centimeter
Acceptable Salt Type: Sodium Chloride
All Systems above tested at 35 psi +/- 5 psi, pH of 7.5 +/- 0.5, Capacity Testing Flow Rate = 50% of the rated service flow rate for
the various size systems .
These water softener systems have been tested by WQA and conform to NSF/ANSI 44
for specific performance claims as verified and substantiated by test data. The rated salt
efficiencies above were also determined in accordance with NSF/ANSI 44 and are only valid
at the salt dosage referenced above. An efficiency rated water softener is a demand initiated
regeneration (DIR) softener which also complies with specific performance specifications
intended to minimize the amount of regenerant brine and water used in its operation.
Efficiency rated water softeners shall have a rated salt efficiency of not less that 3350 grains
of total hardness exchanged per pound of salt (based on NaCl equivalency) (477 grams of total
hardness exchanged per kilogram of salt), and shall not deliver more salt than its listed rating.
The rated efficiency of the water softener, the salt dosage at that efficiency, the capacity at
that salt dosage and that of the efficiency is only valid at the stated salt dosage. Efficiency is
measured by a laboratory test described in NSF/ANSI 44. The test represents the maximum
possible efficiency the system can achieve. Operational efficiency is the actual efficiency
achieved after the system has been installed. It is typically less than the efficiency due to
individual application factors including water hardness, water usage, and other contaminants
that reduce the water softener's capacity. These systems are not intended to be used for
treating water that is microbiologically unsafe or of unknown quality without adequate
disinfection before or after the system. Refer to the system Installation and Service Manals for
set-up and programming instructions. Contact your local dealer for parts and service. See your
owner's manual for warranty information.Iowa Requirement:
Seller: ________________________________________________ Date:
_________________________
Buyer: ________________________________________________ Date:
_________________________
22 •
OM26KCS
8
9
11,447 @ 2 .7
13,755 @ 3 .3
21,330 @ 8 .5
25,631 @ 10 .4
26,111 @ 13 .15
31,376 @ 16 .0
4,226 @ 2 .7 lbs .
4,160 @ 3 .3 lbs .
2 .1
0 .82 ft
per tank
1 .0 ft
3
9" x 35"
, Operating Temperature: 34 - 110° F or 1 .1 – 43 .3° C
2
OMNIFILTER
13845 Bishops Dr., Suite 200
Brookfield, WI 53005
PH: (800) 279-9404
OM32KCS
OM36KCS
10
11
15,821 @ 3 .6
29,481 @ 11 .3
36,089 @ 17 .5
4,400 @ 3 .6 lbs .
2 .7
per tank
1 .09 ft
3
10" x 35"
10" x 35"
OM40KCS
11
11
13 .5
15
18,143 @ 4 .12
33,809 @ 12 .97
41,386 @ 20 .0
4,400 @ 4 .12 lbs .
2 .7
2 .7
per tank
1 .25 ft
3
3
10" x 35"
Tested and Certified
by WQA to NSF/ANSI
Standard 44 & 372 for
softener performance
& lead free compliance
and CSA B483 .1 .
per tank

Publicidad

loading

Este manual también es adecuado para:

Omnifilter om32kcsOmnifilter om36kcsOmnifilter om40kcs