EINHELL TE-RH 32 E Manual De Instrucciones Original página 19

5.2 Depth stop (Fig. 3 – Item 7)
The depth stop (7) is held in place with the lo-
cking screw (a) on the additional handle (6) by
means of a clamp.
•
Undo the locking screw (a) and fit the depth
stop (7).
•
Set the depth stop (7) to the same level as
the drill bit.
•
Pull the depth stop (7) back by the required
drilling depth.
•
Retighten the locking screw (a).
•
Now drill the hole until the depth stop (7) tou-
ches the workpiece.
5.3. Tool insertion (Fig. 4)
•
Clean the tool before insertion and apply a
thin coating of drill bit grease to the shaft of
the tool.
•
Pull back and hold the locking sleeve (2).
•
Insert the dust-free tool into the tool mounting
as far as it will go whilst turning it. The tool will
lock itself.
•
Check that it is properly secure by pulling the
tool.
5.4 Tool removal (Fig. 5)
Pull back and hold the locking sleeve (2) and re-
move the tool.
6. Operation
Danger
To prevent all danger, the machine must only be
held using the two handles (6/8). Otherwise there
may be a risk of suff ering an electric shock if you
drill into cables.
6.1 Status indicator (Fig. 1/Item 11)
The status indicator (11) lights up when the power
plug is connected.
6.2 Switching On and Off (Fig. 1)
To switch on: Press and hold the operating switch
(4).
To switch off : Let go of the operating switch (4)
6.3 Adjusting the speed (Fig. 1/Item 4)
•
Infinitely variable speed control is possible
during operation.
•
Select the speed by applying a greater or les-
ser pressure to the ON/OFF switch (4).
•
Select the correct speed: The most suitable
Anl_SA_TE_RH_32_E_SPK8.indb 19 Anl_SA_TE_RH_32_E_SPK8.indb 19
GB
speed depends on the workpiece, the type of
use and the drill bit used.
•
Low pressure on the ON/OFF switch (4): Lo-
wer speed
•
Greater pressure on the ON/OFF switch (4):
Higher speed
6.4 Hammer stop facility (Fig. 6)
The hammer drill has a hammer stop facility for
gentle initial drilling.
•
Turn the rotary switch for the hammer stop
facility (5) to position (B) to switch off the
hammer facility.
•
To switch on the hammer facility again the
rotary switch for the hammer stop facility (5)
must be turned back to position (A).
6.5 Rotation stop facility (Fig. 7)
•
For hammer drilling, press the button (E) on
the rotary switch (3) and simultaneously turn
the rotary switch (3) to position A.
•
For chiseling, press the button (E) on the rota-
ry switch (3) and simultaneously turn the rota-
ry switch (3) to position B. In switch position B
the chisel is not locked.
•
For chiseling, press the button (E) on the
rotary switch (3) and simultaneously turn the
rotary switch (3) to position C. The chisel is
locked in position C.
Important.
Please note that it is not possible to operate the
hammer drill with the hammer stop and rotation
stop facilities both active at the same time.
Important.
Only low pressure is required for hammer drilling.
Excessive pressure will exert an unnecessary
force on the motor. Check the drill bits at regular
intervals. Sharpen or replace blunt drill bits.
6.6 Press control (Fig. 8/Item 9)
To ensure the ideal contact pressure, the press
control (9) must be in the green range.
The indicator serves only as a guide and
should not be observed permanently.
- 19 -
10.02.16 13:48 10.02.16 13:48