Etac R82 Multi Frame Manual Del Usuario página 37

Safety
Signs, symbols and instructions placed on this product must never be covered or removed and must remain present
and clearly legible throughout the entire lifetime of the product. Immediately replace or repair illegible or damaged
signs, symbols and instructions. Contact your local dealer for instructions.
Any adverse event in relation to the device must be reported to your local dealer and the national competent
authority in a timely manner. The local dealer will forward information to manufacturer.
Caregiver
• Read the "User Guide" carefully before use and
keep it for future reference. Incorrect use of this
product may cause serious injury to the user
• This product contains small parts which could
present a choking hazard if removed from their
intended placing
• Always use the correct lifting techniques and aids
for this purpose
• Never leave the user unattended in this product.
Ensure permanent supervision by a caregiver
• Repair/replacements must only be made using
new original R82 spare parts and fittings and
carried out in accordance with the guidelines and
service intervals prescribed by the supplier
• Be aware of any MAX mark indications before
adjustment
• Ensure that moving parts does not squeeze or
trap body parts when adjusting them
• Ensure that body parts are not trapped in
openings for mounting of supports/accessories.
• If there is any doubt as to the continued safe use
of your R82 product or if any parts should fail,
stop using the product immediately and contact
your local dealer as soon as possible
• Always use the product in a moderate pace. Do
not run with the product
• Information regarding frame and seat
combinations including max. load in combination
can be found at: etac.com
• Information about transportation can be found in
the document "M1460 Transportation in Motor
Vehicles" supplied with the product
• Information about roadability can be found in the
document "Roadability" supplied with the product
Environment
• Observe the surface temperature on the product,
before placing an user in it. This goes especially
for users with insensitive skin as they cannot
feel the heat. If the surface temperature is above
41°C then allow the product to cool before use
User
• If the user is close to the max. load limit and/or
has a lot of involuntary movements, e.g. rocking,
a larger size with a higher max. load or a different
R82 product should be considered
Product
• Carry out all positional adjustments on the
product and accessories and ensure that all
knobs, screws and buckles are securely fastened
before use. Keep all tools out of the reach of
children
• Removable parts without use of tool: wheels
and foot support. The removal will have adverse
effect on the device
• Ensure the stability of the product is maintained
before placing the user in it
• Activate the brakes before placing the user into
the product
EN
• Activate the anti-tips before angling the seat and
back
• Deactivate the anti-tips when forcing kerbs higher
than 100 mm
• We recommend you notify the user before angling
the seat and back
• Ensure the wheels are fully-functional and secure
before use
• The correct tyre pressure is printed on the tyre
casing and listed in the section for tyre technical
data.
• In case of a tyre puncture do not use the product
until remedied
• Unoccupied device is suitable for land and air
transport
• Attaching additional loads can adversely affect
stability. Position of points intended to carry
additional loads are specified in the relevant
Mounting Guide referred to under section for
accessories
• Do not expose the gas spring to pressure or high
temperatures. DO NOT puncture
• Inspect the product and all of its accessories and
replace any worn out parts before use
• This product is tested for resistance to ignition at
level non-ignition in accordance with EN 1021-1,
EN 1021-2 and ISO 7176-16
• The product might lose its flame resistant
characteristics if using other than original R82:
Cushions
• The product is approved for transportation
in vehicles according to ISO 7176-19. More
information can be found in the document
"M1460 Transportation in Motor Vehicles"
supplied with the product.
• In accordance with ISO 7176-19 Annex D, the
product is evaluated regarding the ability to
accommodate vehicle-anchored pelvic and
shoulder belts. The device receives an overall
score of "Good"
37
etac.com