Publicidad
Idiomas disponibles
Idiomas disponibles
English
Push Block (Fig. EE, FF)
iMPORTAnT: Only use the push block
63
Rip Auxiliary Fence. The push block should be used once the material being cut reaches the saw
table top.
1. Construct a push block using the diagram in Figure EE.
nOTE: Edges
64
must be parrallel.
iMPORTAnT: The over hanging edge
65
the push block to slip or push the material away from the fence.
Fig. EE
4-3/4"
5"
(121 mm)
(127 mm)
64
1/2"
12"
(12.7 mm)
(305 mm)
2-1/2"
(64 mm)
5-1/4"
1/2"
(133 mm)
(12.7 mm)
63
2. Place the push block
(Fig. FF) behind the material and ensure the lip of the block is flush
60
to the narrow rip auxiliary fence
.
3. Once the push block is in place, continue feeding the material until the cut is complete
making sure the push block remains flush to the narrow rip auxiliary fence at all times.
iMPORTAnT: The narrow rip auxiliary fence and the over hanging edge
be the same thickness.
Fig. FF
Featherboard Construction (Fig. GG, HH)
Featherboards are used to keep the work in contact with the fence and table, and help prevent
kickbacks. Dimensions for making a typical featherboard are shown in Figure GG. Make
the featherboard from a straight piece of wood that is free of knots and cracks. Clamp the
featherboard to the fence and table so that the leading edge of the featherboard will support the
workpiece until the cut is complete (Fig. HH). An 8" (203 mm) high flat board can be clamped to
the rip fence and the featherboard can be clamped to the 8" (203 mm) high board.
Fig. GG
24" (610 mm)
The kerf should
be about 1/4"
4"
(6.4 mm) apart
(102 mm)
WARNING: Use featherboards for all non thru-sawing operations where the blade guard
assembly, anti-kickback assembly and riving knife cannot be used. Always replace the
blade guard assembly, anti-kickback assembly and riving knife when the non thru-
sawing operation is complete. Make sure the featherboard presses only on the portion of
the workpiece in front of the blade.
Fig. HH
14
with the narrow rip auxiliary fence, refer to Narrow
Fig. EE) MUST be square. An uneven lip could cause
1/2"
(12.7 mm)
65
Fig. EE) should both
63
60
5" (127 mm)
MAINTENANCE
WARNING: To reduce the risk of serious personal injury, turn unit off and remove the
battery pack before making any adjustments or removing/installing attachments
or accessories. An accidental start-up can cause injury.
Cleaning
WARNING: Blow dirt and dust out of all air vents with clean, dry air at least once a week.
To minimize the risk of eye injury, always wear ANSI Z87.1 approved eye protection when
performing this procedure.
WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts
of the tool. These chemicals may weaken the plastic materials used in these parts. Use a
cloth dampened only with water and mild soap. Never let any liquid get inside the tool; never
63
immerse any part of the tool into a liquid.
Accessories
WARNING: Since accessories, other than those offered by D
this product, use of such accessories with this tool could be hazardous. To reduce the risk of
injury, only D
WALT recommended accessories should be used with this product.
e
Recommended accessories for use with your tool are available at extra cost from your local dealer
65
or authorized service center. If you need assistance in locating any accessory, please contact
D
WALT Industrial Tool Co., 701 East Joppa Road, Towson, MD 21286, call 1–800–4-D
e
(1–800–433–9258) or visit our website: www.dewalt.com.
•
Compatible Stands (DWE74911)
•
Metric rip scale (N692656)
•
Dust extraction Y connector (contact your local dealer)
Repairs
The charger and battery pack are not serviceable.
WARNING: To assure product SAFETY and RELIABILITY, repairs, maintenance and
adjustment (including brush inspection and replacement) should be performed by a
D
WALT factory service center or a D
e
replacement parts.
Register Online
Thank you for your purchase. Register your product now for:
WARRAnTY sERViCE: Registering your product will help you obtain more efficient warranty
•
service in case there is a problem with your product.
COnFiRMATiOn OF OWnERshiP: In case of an insurance loss, such as fire, flood or theft,
•
your registration of ownership will serve as your proof of purchase.
FOR YOUR sAFETY: Registering your product will allow us to contact you in the unlikely
•
event a safety notification is required under the Federal Consumer Safety Act.
Register online at www.dewalt.com/register.
Three Year Limited Warranty
For warranty terms, go to https://www.dewalt.com/Legal/Warranty/3-Year-Limited-Warranty.
To request a written copy of the warranty terms, contact: Customer Service at D
Tool Co., 701 East Joppa Road, Towson, MD 21286 or call 1-800-4-D
lATin AMERiCA: This warranty does not apply to products sold in Latin America. For products
sold in Latin America, see country specific warranty information contained in the packaging, call
the local company or see website for warranty information.
FREE WARning lABEl REPlACEMEnT: If your warning labels become illegible or are missing,
3/4"
call 1-800-4-D
WALT (1-800-433-9258) for a free replacement.
e
(20 mm)
WALT, have not been tested with
e
e
WALT authorized service center. Always use identical
e
WALT Industrial
e
WALT (1-800-433-9258).
e
WALT
Publicidad
