Publicidad
Idiomas disponibles
Idiomas disponibles
11) VOX ~ NOISE GATE ~ VOX SETTING
VOX
(short press)
The VOX function allows
transmitting
phone (or in the optional vox microphone) without pressing the PTT switch
(18). The use of an optional vox microphone connected to the rear panel
disables
of the transceiver (E)
Short press the VOX key (11) in order to
appears on the display. Short press again the VOX key (11) to
function. "VOX" disappears.
NOISE GATE
(combination 14 + 11)
Short press the F key (14).
-
appears on the display,
-
Short press the VOX key (11) to
GATE. "
" is displayed when the function is active.
Noise Gate: Prevents amplification of background noise. This results in
optimized signal levels.
VOX SETTING
(long press)
1.
Long press the VOX key (11) to
current setting and its value appear on the display. Three parameters allow
to adjtust the VOX: Sensitivity
time
.
2a. Turn the CH rotary knob (4) or use the UP/DN keys (19) on the microphone
to
modify
the current parameter then, press the F key (14) to
parameter or....
2b. Press first the F key (14) to
select
CH rotary knob (4) or use the UP/DN keys (19) on the microphone to
the current parameter.
3.
When all adjustments are done, press PTT switch (18) to
KEY BEEP function is activated, a long beep sounds to
of the operation (consul the KEY BEEP menu page 51).
4.
If no key is pressed for 10 seconds, the unit automatically
VOX SETTING without save.
Sensitivity
-
: allows the adjustment of the microphone (original one
or optional vox) for an optimum transmission quality. Adjustable level from1
(high level) to 9 (low level). Default value: 5.
Anti-Vox
-
: allows disabling the transmission generated by the sur-
rounding noise. The level is adjustable. AF (according the squelch level)
and from 0 (without anti-vox) to 9 (low level). Default value: AF.
by speaking into the original micro-
the original microphone.
activate
the VOX function. "VOX"
disable
activate
(On) or
deactivate
(OF) the NOISE
enter
the VOX SETTING. "VOX" blinks, the
/ Anti-vox level
/ Vox delay
select
another the parameter and then turn the
store
and exit. If the
confirm
the success
exits
the function
-
Delay time
adding a delay at the end of speaking. The level is adjustable from 1 (short
delay) to 9 (long delay). Default value: 1.
VOX SETTING doesn't activate the VOX function.
12) NRC ~ REPEATER/RELAY
NRC
(short press)
This switchable filter can be used to improve reception and transmission
the
modes..
Press the NRC key (12) to activate/deactivate the NRC in this order:
-
1- NRC RX LED is green
2- NRC TX LED is red
3- NRC RX + TX LED is orange
4- NRC Off LED is off.
See NRC SET menu page 16.
REPEATER/RELAY
WARNING! This function is valid only on the D frequency band. See the
configuration table page 74.
This function lets you extend the range of your transceiver by using relays..
The radio receives on the current channel and transmits on the defined
next
channel.
To activate this function you must define a TX channel (See REPEATER/RELAY
SETTING menu page 55).
modify
-
Short press the F key (14).
Short press the NRC key (12) to
-
the REPEATER/RELAY function. The selection or "
sion channel has not still been selected, blinks during 3 seconds.
When this function is active, the frequency of the RX receive channel and
the TX transmit channel is displayed. When transmitting, the TX channel is
displayed and flashes.
13) TALKBACK
(short press)
This function allows you to
or external speaker connected to the EXT.SP jack (C).
Short press the TB key (13) to
When the function is active, the LED is lit.
49
: allows avoiding the sudden cut of the transmission by
(combination 14 + 12)
appears on the display,
activate
deactivate
or
hear
your own modulation in the optional internal
activate /deactivate
the TALKBACK function.
", if the transmis-
Publicidad
