EINHELL GC-ET 4530 Manual De Instrucciones página 9

5) Whenever the tool begins to make unusual
vibrations.
h) Beware of injuries to feet and hands caused
by the cutting unit.
i) Always make sure that the air vents are kept
free of foreign objects.
Maintenance and storage
a) Disconnect the tool from the power source
(i.e. pull the power plug out of the power sock-
et) before you carry out any maintenance or
cleaning work on it.
b) Use only spare parts and accessories which
are recommended by the manufacturer.
c) The tool must be inspected and serviced
regularly. Have the tool repaired only in an
authorized service center.
d) When the tool is not being used it must be
kept out of children's reach.
Recommendation
The tool should be supplied with a trip current
of no more than 30 mA via a residual current
protective device (RCD).
Never replace the non-metal cutting unit with a
metal cutting unit.
Risk of injury from dangerous moving parts!
Take care to avoid abnormal working postures
and to always keep your balance so that you
stand squarely on inclines at all times. Walk, don't
run.
Take care not to touch moving hazardous parts
before the tool has been disconnected from the
power source and the moving hazardous parts
have come to a complete standstill.
Before use, the power cable or the extension
cable must be checked for signs of damage or
wear. If the power cable becomes damaged
during use, disconnect the cable immediately
from the power source. Under no circumstances
are you allowed to touch the cable before it is
separated from the power source.
Never connect a damaged power cable to the
power source, and never touch a damaged cable
before it has been disconnected from the power
source – damaged cables might result in you
touching active parts.
Anl_GC_ET_4530_SPK7_USA.indb 9 Anl_GC_ET_4530_SPK7_USA.indb 9
EN
Keep extension cables away from dangerous
moving parts in order to prevent damage to
cables that might result in you touching active
parts.
Avoid using the tool in poor weather conditions,
especially if there is a risk of lightning.
When working outdoors, use only extension cords
which are approved for outdoor use. Extension
cords must have a minimum 16 wire size (A.W.G.)
and are not allowed to be of a lighter wire size
class than 16 (A.W.G). Extension cords are not
allowed to exceed a maximum length of 164 ft.
(50 m). Plug connections must have earthing
contacts and be protected from rain water.
&
Servicing of Double Insulated Appliances
Your blower is double-insulated to give you
added safety. In a double insulated appliance,
two systems of insulation are provided instead
of grounding. No grounding means is provided
on a double insulated appliance, nor should a
means for grounding be added to the appliance.
Servicing a double insulated appliance requires
extreme care and knowledge of the system
and should be done only by qualifi ed service
personnel. Replacement parts for a double
insulated appliance must be identical to the
parts they replace. A double insulated appliance
is marked with the words double insulated or
"double insulation". The symbol (square within a
square) may also be marked on the appliance.
Additional safety instructions
•
Before you begin your work, examine the
material you want to cut. Remove any foreign
objects. Continue to watch out for foreign
objects while you are working. If you come
across any foreign objects while cutting, turn
off the machine and remove the items in
question.
•
Work only when visibility is adequate.
•
Make sure you stand squarely at all times
while working. Be careful when walking
backwards. Tripping hazard!
•
Never leave the equipment unsupervised in
the work area. If you stop work for a while,
leave the equipment in a safe place.
•
If you stop your work in order to go to another
area to work, you must make sure that the
equipment is switched off while you are going
there.
- 9 -
21.12.2022 08:57:24 21.12.2022 08:57:24