Publicidad
Idiomas disponibles
Idiomas disponibles
EN
However, if anybody is transmitting on the channel, all sub
channels will be busy during that time. If the sub channel
feature is switched off, all communication on a channel will
be heard. Press the (+) button (A:10) or (–) button (A:11) to
select the sub channel. The LiteCom headset supports
Continuous Tone Coded Squelch System (CTCSS) and
Digital Coded Squelch (DCS) for a total of 38 frequencies/
codes (see table above for sub channel number and the
associated tone/code). To switch this function off press the
(–) button when sub channel 1 is selected, or press the (+)
button when channel 38 is selected. Press the (+) button to
switch this function back on.
3.10 PTT (Push-To-Talk)
Press and hold the PTT button (for built-in two-way radio or
for auxiliary two-way radio) to open the two-way radio
channel and then speak in to the microphone.
NOTE: When pushing the PTT button, the headset will
always transmit a signal regardless of the BCLO setting.
3.11 Reset to factory defaults
To restore the headset to factory default settings the unit
must first be switched off. Then press and hold the (+)
(A:10) and (–) (A:11) buttons at the same time while also
pressing the (A:9) On/Off/Mode button. This is confirmed
by the voice message "restore factory defaults".
4. CLEANING AND MAINTENANCE
Use a cloth wetted with soap and warm water to clean the
outer shells, headband and ear cushions.
NOTE: Do NOT immerse the hearing protector in water.
If the hearing protector gets wet from rain or sweat, turn
the earmuffs outwards, remove the ear cushions and foam
liners, and allow to dry before reassembly. The ear
cushions and foam liners may deteriorate with use and
should be examined at regular intervals for cracking or
other damage. When used regularly, 3M recommends
replacing the foam liners and ear cushions at least twice
a year to maintain consistent attenuation, hygiene, and
comfort. If an ear cushion is damaged, it should be
replaced. See Spare Parts Section below.
4.1 Removing/replacing ear cushions
E:1
E:2
(E:1) To remove the ear cushion, slide your fingers under
the edge of the ear cushion and firmly pull straight out.
(E:2) Replace the foam liners.
(E:3) Fit one side of the ear cushion into the groove of the
earcup and then press on the opposite side until ear
cushion snaps in place.
5
REPLACING THE HELMET ATTACHMENT PLATE
For proper fitting on different industrial safety helmets, the
helmet attachment plate may need to be replaced. Find the
recommended attachment in Table C. The headset comes
assembled with P3E helmet attachment. Plates for P3K
helmet attachment assembly are also included in the box,
while other plates can be obtained from your dealer. A
screwdriver is needed to replace the helmet attachment
plate.
(F:1) Loosen the screw holding the plate and remove the
plate.
(F:2) Attach the appropriate plate while ensuring the left (L)
and right (R) designated plates are on the appropriate
earmuff, if applicable, and then tighten the screw.
5. SPARE PARTS/ACCESSORIES
3M™ PELTOR™ HY79 Hygiene kit
Replaceable hygiene kit consisting of two attenuation
cushions, two foam rings and two snap-in ear cushions.
Replace at least twice a year to ensure constant
attenuation, hygiene and comfort.
3M™ PELTOR™ HY100A Single-use protectors
A single-use protector that is easy to fit to the ear cushions.
Pack of 100 pairs.
3M™ PELTOR™ HYM1000 Microphone protector
Moisture-resistant and wind-resistant hygienic tape that
protects the speech microphone and extends its life at
the same time. Pack of 5 metres is sufficient for around
50 replacements.
3M™ PELTOR™ M995 Wind shield for electret
microphone
Effective protection from wind noise for electret
microphone that also protects it and extends its life.
3M™ PELTOR™ FR08 Power supply
E:3
Power supply for FR09/ACK053.
3M™ PELTOR™ACK053 Rechargeable battery
NiMH rechargeable battery that can replace two
AA type 1.5 V standard batteries.
3M™ PELTOR™ FR09 Battery charger
Charger for ACK053.
3M™ PELTOR™ 1180 SV Battery cover
3M™ PELTOR™ MT53N-12 Electret microphone
Supplied as standard with product.
F:1
F:2
Publicidad
