GRAPHITE 58G011 Manual Del Usuario página 10

1 Read the operating instructions and observe the warnings and
safety conditions contained therein.
2 Wear safety goggles and ear protection.
3 Work in a protective mask.
4 Keep children away from the unit.
5 Protect from rain.
6 Indoor use, protect from water and moisture.
7 Caution, sharp parts!
8 Wear protective gloves.
9 Recycling.
10 Second class protection.
11 Selective collection.
12 Do not dispose of the cells in a fire.
13 Hazardous to the aquatic environment.
14 Do not allow heat to rise above 50°C.
CONSTRUCTION AND APPLICATION
The jigsaw is a hand-held device powered by a battery. It is driven by a
DC commutator motor. The device is intended for making straight split cuts,
curved cuts and cuts in wood, wood-based materials, plastics and
metals (provided a suitable saw blade is used).
Its areas of use are the execution of renovation and
construction and all work in the area of independent amateur activity
(DIY).
Do not use the device for purposes other than those for
which it was intended
DESCRIPTION OF THE GRAPHIC PAGES
The following numbering refers to the components of the device
shown on the graphic pages of this manual.
1 Switch lock button
2 Switch
3 Adapter
4 Foot
5 Swing motion control switch
6 Blade holder
7 Guide roller
8 Parallel guide lock screws
9 Protective rod
10 Cover
11 Lighting
12 Battery retaining button
13. Battery
14 Charger
15 LEDs
16 Battery charge indicator button
17 Battery charge status indication (LEDs).
18 Parallel guide
* There may be differences between the drawing and the product.
INSTALLATION/SETTING
EQUIPMENT AND ACCESSORIES
1 Hexagonal spanner
2 Parallel guide - 1 pc.
PREPAREDNESS FOR WORK
REMOVING / INSERTING THE BATTERY
• Press the battery retaining button (12) and pull out the battery
• Insert the charged battery (13) into the holder in the handle until the
BATTERY CHARGING
The device is supplied with a partially charged battery. The battery
should be charged in conditions where the ambient temperature is
between 40°C and 40°C. A new battery or one that has not been used
for a long time will reach its full capacity after approximately 3 - 5
charge and discharge cycles.
• Remove the battery (13) from the unit (fig. A).
• Plug the charger into a mains socket (230 V AC).
• Slide the battery pack (13) into the charger (14) (Fig. B). Check
When the charger is plugged into the mains socket (230 V AC), the green
LED (15) on the charger will illuminate to indicate that voltage has been
applied.
When the battery (13) is placed in the charger (14), the red LED (15) on
the charger lights up to indicate that the battery is being charged.
At the same time, the green LEDs (17) of the battery charge status in
the various arrangements (see description below) light up pulsatingly.
• Flashing of all LEDs - indicates low battery and the need to
• Pulsating light of 2 diodes - indicates partial discharge.
• Pulsating light of 1 diode - indicates high level of battery
When the battery has been recharged, the LED (15) on the charger
lights up green and all the battery charge status LEDs (17) glow
continuously. The battery charge status LEDs (17) switch off after a certain
time (approx. 15s).
The battery should not be charged for more than 8 hours.
Exceeding this time may damage the battery cells. The charger
will not switch off automatically when the battery is fully
charged. The green LED on the charger will remain lit. The
battery charge status LED will turn off after some time.
Disconnect the power before removing the battery from the
charger socket. Avoid consecutive short charges. Do not
recharge the batteries after a short period of use. A significant
drop in the time between necessary charges indicates that the
battery is worn out and should be replaced.
Batteries become very warm during the charging process. Do
not start work immediately after charging - wait until the
battery has reached room temperature. This will prevent
damage to the battery.
BATTERY CHARGE LEVEL INDICATION
The battery is equipped with a charge level indicator (3 LEDs)
(17). To check the charge level of the battery, press the battery
charge level indicator button (13) (Fig. C). When all LEDs are lit,
the battery charge level is high. When 2 diodes are lit it means that the
battery is partially discharged. When only 1 diode is lit it means that the
battery is exhausted and needs to be recharged.
INSTALLATION OF PARALLEL CUTTING GUIDE
The parallel cutting guide can be mounted on the right or left side of the
machine foot.
• Loosen the parallel guide lock screws (8).
• Insert the parallel guide bar (18) into the holes in the foot (4), set the
The guide bar of the parallel guide should be facing downwards.
The parallel guide (18) can also be used for mitre cuts from 0° to
45°.
BLADE FIXING
The blade is mounted and replaced without tools.
Blade mounting
- 1 pcs.
(13) (fig. A).
battery retaining button (12) audibly engages.
that the battery is properly seated (inserted all the way in).
recharge the battery.
charge.
desired distance (using the graduation marks) and fix it by tightening
the parallel guide bar locking screws (8) (fig. D).