Stiga P 901 C Serie Manual De Instrucciones página 71

The engine may be very warm immediately after
it is shut off. Do not touch the exhaust or adjacent
parts. This can cause burn injuries.
5.6. AFTER USE
• Allow the engine to cool before storing in an enclosed space.
• Clean (par. 6.3).
whenever the machine is left unattended, the operator leaves
the driving seat or parks the machine:
1. Stop the machine.
2. bring the cutting means assembly to the lowest height
position.
3. Make sure that all moving parts have come to a com-
plete stop.
4. Remove the ignition key.
6. MAINTENANCE
The safety regulations to be followed are described in chapter
1. Strictly comply with these instructions to avoid serious
risks or hazards:
Before c ommencing a ny i nspections, c leaning o r m aintenance/
adjustments on the machine:
• Disengage the cutting means.
• Stop the machine.
• Shift into neutral.
• Engage the parking brake.
• Stop the engine.
• Make sure that any moving component has stopped.
• Remove the ignition key.
• Use suitable clothing, protective gloves and goggles.
IMPORTANT Never leave the key inserted or within reach of
children or unauthorized people.
6.1. REFUELLING
For tank capacity see "0 TABLE OF TECHNICAL DATA".
To refuel:
1. Unscrew the fuel tank filler cap (fig.20.A) and remove it.
2. Refuel being careful not to completely fill the tank. Leave
some space (corresponding at least to the entire filler neck
+ 1 - 2 cm at the top of the tank) so that, when the petrol
heats up, it can expand without overflowing.
3. Close the fuel cap securely after refuelling and clean
away any spills.
IMPORTANT Use only unleaded petrol. Do not mix petrol
with oil.
IMPORTANT Do not drip petrol onto the plastic parts to avoid
ruining them. In the event of accidental leaks, rinse immediately
with water. The warranty does not cover for damage to plastic
parts of the bodywork or the engine caused by petrol.
6.2. CHECK AND TOP-UP ENGINE OIL
NOTE For the oil type to be used, see "0 TECHNICAL DATA
TABLE".
IMPORTANT Observe the precautions provided in the engine
owner's manual.
Always check the oil level before use.
1. Clean around the dipstick.
2. Unscrew and remove the dipstick.
3. Clean the dipstick.
4. Insert the rod completely, without screwing it in position.
5. Pull out the dipstick again and check the oil level.
6. If the level is low, top up to the upper limit mark (18).
6.3. CLEANING
• General instructions
Before each use, clean thoroughly following the instructions
below:
• Do not spray water onto the motor and electrical
components and prevent them from getting wet.
• Remove grass debris and mud accumulated inside the
chassis.
• Always make sure the air intakes are free of debris.
• Do not use aggressive liquids to clean the chassis.
• To reduce the risk of fire, keep the engine free of grass,
leaves residues or excessive grease.
1. Clean the engine cooling air intake (18:A).
2. After cleaning with water, start the machine and the and
the cutting means assembly installed on it to remove the
water that may otherwise infiltrate in the bearings and
cause damages.
6.4. BATTERY
Carefully read and observe the battery recharging instructions
in the booklet provided with the battery. Failure in following
the procedure or in charging the battery could permanently
damage the battery elements. A flat battery must be recharged
as soon as possible.
Charge through the engine:
1. In the case of a new battery, connect the cables to
the battery.
2. Take the machine outdoors.
3. Start the engine according to the instructions in this
manual.
4. Leave the engine running continuously for 45 minutes
(time needed to fully charge the battery).
5. Stop the engine.
Charging by battery charger.
IMPORTANT Recharging must be done using a battery
charger at constant voltage. Other recharging systems can irre-
versibly damage the battery.
EN - 6