cecotec BONGO D20 MOBILE Manual De Instrucciones página 34

ENGLISH
4. PRODUCT ASSEMBLY
Unfolding
1. Detach the retaining bracket and pull the stem upwards.
2. Raise the stem and move the folding lever to the closed position to lock the stem in place.
3. Adjust the brakes with the Allen key.
Folding Fig. 25
1. Press the blue plate to release the folding lever.
2. Move the folding lever.
3. Turn the folding lever downwards and then the stem.
4. Align the locking hook with the hole in the retaining bracket.
Assembly of the handlebar
1. Connect the male connection cord of the handlebar to the female cord of the stem. Make
sure the male and female ports are correctly aligned.
2. Insert the handlebar into the top of the stem and screw it in place.
3. Attach the phone mount to the handlebar.
Precaution:
Be careful not to damage the cord during the process.
Checking the screws
Some of the screws of the electric scooter may loosen during delivery. Please check all screws
and tighten them before turning on the electric scooter.
5. OPERATION
5.1. Switch-on and driving Fig. 23
1. Hold down the power button for 2 seconds.
2. Step on the deck with one foot and use the other one to propel yourself forward.
3. Place both feet on the deck.
4. Press the accelerator with your right hand. The electric motor will deliver power when the
speed of the scooter is equal to or greater than 3 km/h.
5. Press the accelerator to increase the speed.
6. Push the brake lever to stop or to ride more slowly.
7. Get off the electric scooter only when you ride at a very low speed or when you are still.
8. Fold down the kickstand (15, Fig. 22) to park the electric scooter when not in use.
5.2 Driving modes Fig. 23
66 ORIGINAL MANUAL TRANSLATION
Control panel
Power button:
- Long press: switch the electric scooter on or off.
- Short press: switch between the following modes:
1. PEDESTRIAN mode: the mode indicator on the display will show a person walking. In this
mode, the scooter can reach 6 km/h. The tail light will flash when driving in this mode.
2. COMFORT mode: In this mode, the scooter can reach 15 km/h.
3. SPORT mode: the mode indicator on the display will show a white "S". In this mode, the
scooter can reach 20 km/h.
NOTE: measured with a weight of 80 kg, fully charged battery, flat surface, no inclination, no
wind, and an ambient temperature of approx. 25 ºC.
Function button:
- Short press: switch the scooter lights on or off.
- Long press (3 seconds): enter the settings menu.
Settings menu
- Once inside the settings menu, press the power button to switch between P0, P1, R0, and
R1.
- Press the function button to navigate between the different settings functions (P0 and P1).
Access the desired function by pressing the power button and toggle between 0 and 1 by
pressing the function button. Select the desired setting by pressing the power button. To
return to the main settings menu, wait a few seconds without pressing any buttons. The
different settings functions are:
1. P0 - Units of measurement: km/h (0) or mph (1). Speed can be measured in kilometres per
hour (0) or miles per hour (1).
2. P1 - Total trip distance measurement (ODO) or current trip (TRIP).
5.4 Wheel use
- For a correct operation of the electric scooter, you should check and ensure the correct
pressure on the wheels before every use.
- The optimum pressure for these wheels is de 50 PSI / 3,4 bars / 344 kPa.
- We recommend you carry out periodic checks to ensure the pressure is within the
recommended values to achieve efficient operation.
- During the shelf life of the wheels, we recommend using heat-sealing gels to prevent
punctures and maintain maximum effectiveness and performance.
ENGLISH
BONGO D20 MOBILE 67