Descargar Imprimir esta página

Bosch GCM 18V-254 D Professional Manual Original página 25

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 54
– Reattach the laser protection cap (8).
Checking and Adjusting the Basic Settings
To ensure precise cuts, the basic settings of the power tool
must be checked and adjusted as necessary after intensive
use.
Experience and suitable special tools are required for this.
A Bosch after-sales service point will handle this work
quickly and reliably.
Aligning the mitre angle indicator (see figure U)
– Bring the power tool into the work position.
– Turn the saw table (12) to the 0° detent (20). The lever
(17) must be felt to engage in the detent.
Checking
The angle indicator(58) must be in line with the 0° mark of
the scale (21).
Setting
– Loosen the screw (59) using a cross-headed screwdriver
and align the angle indicator along the 0° mark.
– Retighten the screw.
Aligning the Angle Indicator (Vertical) (see figure V)
– Bring the power tool into the work position.
– Release the clamping wheel (45).
– Pull the locking lever (46) out and set the bevel angle to
0° with the tool arm.
– Let go of the locking lever (46). The locking lever must be
felt to engage in the position
– Retighten the clamping wheel (45).
Checking
The angle indicator(28) must be in line with the 0° mark of
the scale (27).
Setting
– Loosen the screw (60) using a cross-headed screwdriver
and align the angle indicator along the 0° mark.
– Retighten the screw.
Transporting the Power Tool (see figure W)
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Before transporting the power tool, the following steps must
be carried out:
– Loosen the locking screw (1) if it is tightened. Pull the
tool arm fully forwards and retighten the locking screw.
– Ensure that the depth stop (39) is swung all the way back
and the adjusting screw (38) does not touch anything
when you move the tool arm.
– Bring the power tool into the transport position.
– Remove all accessories that cannot be securely fitted to
the power tool. If possible, transport unused saw blades
in an enclosed container.
– Turn the transport handle (3) so that it is vertical.
Bosch Power Tools
– Carry the power tool by the transport handle (3) or hold it
by the recessed handles (61) on the sides of the saw
table.
Only use the transport devices to transport the power
u
tool and never the protective devices or workpiece
supports.
Maintenance and Service
Maintenance and Cleaning
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.
The retracting blade guard must always be able to move
freely and retract automatically. It is therefore important to
keep the area around the retracting blade guard clean at all
times.
Always remove dust and chips after working by blowing out
with compressed air or using a brush.
Clean the guide roller (11) regularly.
Noise reduction measures
Measures implemented by the manufacturer:
– Soft start
– Provided with a saw blade specially developed for noise
reduction
Measures implemented by the operator:
– Low-vibration mounting on a stable work surface
– Use of saw blades with noise-reducing functions
– Regular cleaning of the saw blade and power tool
After-Sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
Malaysia
Robert Bosch Sdn. Bhd.(220975-V) PT/SMY
No. 8A, Jalan 13/6
46200 Petaling Jaya
Selangor
Tel.: (03) 79663194
Toll-Free: 1800 880188
Fax: (03) 79583838
E-Mail: kiathoe.chong@my.bosch.com
www.bosch-pt.com.my
English | 25
1 609 92A 7BP | (05.12.2022)

Publicidad

loading

Este manual también es adecuado para:

3 601 m51 13 601 m51 1b