Team Mode ( Two St16 Ground Stations ); Team Mode (Wizard™&St16) - TYPHOON H Manual De Instrucciones

TEAM MODE ( TWO ST16 Ground Stations )

STEP 1) Switch on the original and the new ST16 Ground Stations first, and then
power on Typhoon H. Do not touch it until the initialization completes. Wait a few
seconds for the camera to align and all system (RC and video link) connected.
STEP 2) Tap the 'Model' icon on the new ST16 Ground Station, select TYPHOON H,
and if required press 'OK' to accept any pop up warnings/alerts.
STEP 3) Tap the System Settings icon [
STEP 4) Tap the camera settings icon [
mode to team mode. When the Typhoon H Main LED Status Indicator starts to blink
orange, the aircraft enters binding mode.
STEP 5) Tap the 'Refresh' icon on the new ST16, select the 'SR24_XXXXX' receiver
listed in the column under 'Model', and CGO 3P_XXXXX WiFi listed in the column
under 'camera', type 'Bind' and enter the password '1234567890' to connect the
WiFi, and then tap 'OK' after the connection has been established.
STEP 6) Tap the back button [
the binding is successful.
NOTICE: After the binding completes, the original ST16 Ground Station controls
the CGO3+ gimbal camera, and the new ST16 Ground Station controls the aircraft.
NOTICE: Under the team mode, the new ST16 can't control the gimbal pan and tilt
directions.
IMPORTANT NOTE: The pilot should select 'RealSense Module Installed' in 'Other
Settings' row on the ST16 Ground Station first, then the realsense can be activated.
NOTICE: If there is camera error tips after returning back to the controlling
interface, you can enter into camera select interface to set and choose the camera
type as C-GO3 or C-GO3-PRO, and then tap the return button and return to the
main interface.
If you need to switch back to single mode, the operation steps are as follows:
STEP 1: Tap the settings icon [
mode to single mode.
STEP 2: When the Typhoon H Main LED Status Indicator starts to blink, the aircraft
enters binding mode.
STEP 3: Wait for a few seconds, as the remote control will automatically bind to the
camera and aircraft. You will hear two beeps from the aircraft when the binding is
successful.
] on the new ST16 Ground Station.
System Settings
] on the original ST16, switch from single
] once, you will hear two long beeps, which means
] on the original ST16 and then switch from team
TEAM MODE (Wizard™&ST16)
BINDING TYPHOON WIZARD™ TO TYPHOON H
STEP 1) Power on the ST16 Ground Station first, and then switch on Typhoon
H. Do not touch it until the initialization completes. Wait a few seconds for
the camera to align and all system (RC and video link) connected..
STEP 2) Tap the settings icon [
mode.
STEP 3) When the Main LED Status Indicator starts to blink orange, the
copter enters binding mode.
STEP 4) Press and hold the Power Button of the Wizard until the Aircraft
Mode LED glows solid blue. Do not release the Power Button until hearing
two beeps from the aircraft, then release it.
NOTICE: When Typhoon H is in team mode (Wizard and ST16), the Wizard
must be bound to the copter and the ST16 Ground Station must be bound
to the camera.The default mode of Typhoon H is single mode. The ST16
Ground Station comes bound to the copter from the factory and controls
both the copter and the CGO3+ Gimbal Camera.
When using the Wizard and ST16 Ground Station in team mode, the Wizard
controls the copter and the ST16 Ground Station controls the CGO3+
Gimbal Camera.
If you need to switch back to single mode, the operation steps are as follows:
STEP 1) Tap the settings icon [
switch from team mode to single mode.
STEP 2) When the Main LED Status Indicator starts to blink
orange, the copter enters binding mode.
STEP 3)Wait for a few seconds, as the remote control will
automatically bind to the camera and copter. You will hear
two beeps from the aircraft when the binding is successful.
14
] and then switch from single mode to team
] on the ST16 and then