Publicidad
Idiomas disponibles
Idiomas disponibles
INSTALLATION
General
Flush Built-In Heated Shelves are shipped from the factory
completely assembled and ready for use. Use the following
information and procedures to prepare the unit and the installation
site.
WARNING
ELECTRIC SHOCK HAZARD:
• Plug unit into a properly grounded electrical receptacle
of the correct voltage, size, and plug configuration. If
plug and receptacle do not match, contact a qualified
electrician to determine and install proper voltage and
size electrical receptacle.
• Unit is not weatherproof. Locate unit indoors.
• Remote mounted control enclosure must be mounted on
a vertical wall and installed in vertical position. Mounting
control enclosure in horizontal position may result in
collection of liquids and lead to an electric shock.
FIRE HAZARD: Locate unit a minimum of 25 mm (1") from
combustible walls and materials. If safe distances are not
maintained, combustion or discoloration could occur.
CAUTION
Locate unit at proper counter height in an area that is
convenient for use. The location should be strong enough
to support the weight of unit and contents.
NOTICE
Do not locate unit in area with excessive air movement
around unit. Avoid areas that may be subject to active air
movements or currents (i.e., near exhaust fans/hoods, air
conditioning ducts, and exterior doors).
Do not locate unit in an area subject to excessive
temperatures or grease from grills, fryers, etc. Excessive
temperatures could cause damage to the unit.
Do not turn on unit until it has been cleaned thoroughly.
Ceramic glass surface must be clear of debris to prevent
burn-on.
1. Remove the unit from the box.
NOTE: To prevent delay in obtaining warranty coverage, complete
online warranty registration. See the IMPORTANT
OWNER INFORMATION section for details.
2. Remove tape, protective packaging, and literature from all
surfaces of the unit.
Installing the Unit
1. Prepare the appropriate opening in the countertop for the
unit being installed.
• Refer to the "Countertop Cutout and Mounting Bolt
Dimensions" in this section.
2. Make structural modifications or add bracing underneath
the countertop to ensure the countertop will support the
weight of the unit and its contents.
3. Attach a mounting bracket assembly to the underside of
the prepared countertop at each corner of the cutout.
a. Align the U-shaped mounting holes on the mounting
bracket with the two pre-drilled mounting holes on the
underside of the countertop. The inside surface of the
mounting bracket should be vertically flush with the
inner surface of the countertop cutout.
b. Insert appropriate fasteners through the mounting
bracket and into appropriate anchoring devices in the
mounting holes on the underside of the countertop.
Tighten securely.
4. Install the included self-adhesive gasket around the inner,
vertical surface of the countertop cutout.
• The gasket should be positioned 6 mm (1/4") below the
top surface of the countertop.
NOTE: If the self-adhesive gasket is not available, provide a
caulk backing around the inner, vertical surface of the
countertop cutout 6 mm (1/4ʺ) below the top surface
of the countertop. This will prevent the silicone sealant
applied later in this procedure from falling through the
gap between the countertop and the hot/cold shelf.
5. Carefully lower the heated shelf into the countertop cutout.
This step requires two or more people.
• The heated shelf rests on top of the four leveling bolts,
which are part of the mounting bracket assembly
installed at each corner of the countertop cutout.
6. Adjust the leveling bolts underneath each corner of the unit so
that the shelf is flush or slightly below the countertop surface.
7. Tighten the lock nut on each leveling bolt to secure the
position.
8. Apply a bead of NSF-approved silicone sealant in the gap
between the countertop and the heated shelf. To apply a
clean, consistent sealant bead:
a. Make sure the shelf is centered in the countertop cutout.
b. Install masking tape on each side of the gap to define
the edge of the sealant.
c. Carefully apply sealant into the gap.
d. Quickly smooth the sealant surface.
e. Carefully remove the masking tape before the sealant
dries.
NOTE: The silicone sealant must be rated for use at temperatures
between -23°C (-10°F) and 121°C (250°F).
DO NOT tip unit/mounting surface after final installation.
Unit is free-floating and could fall out if tipped—for
permanent, horizontal installations only.
10
CAUTION
HSBFCEM1-0523
Publicidad
