Hatco HSBF Serie Instrucciones Originales página 15

Daily Cleaning — HSBF-SS Models
Cleaning the Stone Surface
Proper use of the products listed below will not damage the
stone shelf (follow the directions on the product labels).
NOTE: Stone surfaces are a simulated stone solid surface.
CAUTION
After deep cleaning stone surface using abrasives, make
sure to clean and sanitize surface properly before placing
food product.
IMPORTANT NOTE
Flush-mounted units are installed with a bead of silicone
sealant between the unit and the countertop. Use caution
when cleaning with the abrasive pad and avoid contact with
the silicone sealant.
1. Before turning on a HSBF-SS model each day, clean and
sanitize the stone surfaces using a clean, damp cloth and
a sanitizer approved for food contact surfaces. If additional
cleaning is necessary, refer to the following information in
this section.
2. At the end of each day:
a. Turn off the unit and allow to cool.
b. Wipe down all metal surfaces using a clean, damp, non-
abrasive cloth.
c. Clean and sanitize the stone surfaces using a clean,
damp cloth and a sanitizer approved for food contact
surfaces. If additional cleaning is necessary, refer to the
following information in this section.
NOTE: To correct inconsistent staining and discoloration, refer
to the following information in this section.
d. Wipe dry with a clean, non-abrasive cloth.
Hard to Remove Stains
For hard-to-remove stains, use an abrasive pad along with
an abrasive cleaner such as Ajax
Scrub, or Bar Keeper's Friend
available from Hatco (P/N 04.39.049.00). NOTICE: Use an
abrasive pad on stone surface only.
NOTE: Do not use steel wool or metal scouring pads.
Mineral Based Stains
For a mineral-based stain, cleaners designed to remove iron or
rust are recommended and should not harm the stone surface.
Scratches
For scratches, use sandpaper starting with the coarsest grit and
going to finest grit until the scratch disappears. Blend area in
with the supplied abrasive pad.
Daily Cleaning — HSBF-GL Models
Consistent daily cleaning will keep cleanup easy as well as
protect and preserve the glass surface. Make sure to use only
wipes, pads, and cleaners designed specifically for cleaning
ceramic glass surfaces.
1. Before turning on the unit each day, clean the glass surface
using an appropriate cleaning wipe or a damp cloth.
2. At the end of each day:
a. Turn off the unit and allow to cool.
b. Clean the glass surface using an appropriate cleaning wipe
or damp cloth. If additional cleaning is necessary, follow the
"Cleaning Burned-On Residue" procedure in this section.
HSBFCEM1-0523
, Comet , Bon Ami, Magic
® ®
. Additional abrasive pads are
®
Cleaning Sugary/Sticky Spills
To clean sugary/sticky spills, the unit should be warm while
cleaning for easier removal.
1. Turn off the unit and unplug power cord. CAUTION! Burn
Hazard—Heated glass will be hot. Use caution when
touching this area.
2. While unit is still warm, wear an oven mitt and remove the
bulk of the spill using paper towel.
3. Allow the unit to cool.
4. Follow the "Cleaning Burned-On Residue" procedure in
this section to remove the remainder of the spill.
5. Do not use the unit again until the spill has been cleaned
completely.
Pitting or indentation in the glass surface may occur from
sugary spills. If pitting or indentation occurs, the glass surface
must be replaced. To prevent further damage and possible
injury from broken glass, stop using unit immediately and
contact an Authorized Hatco Service Agent.
Cleaning Burned-On Residue
To clean burned-on residue, the use of ceramic glass cleaner
may be necessary.
1. Turn off the unit, unplug power cord, and allow unit to cool.
2. Spread a few drops of ceramic glass cleaner onto the
residue area.
3. Using an appropriate cleaning wipe, rub the residue area
while applying pressure as needed.
4. If residue remains, repeat the steps above as needed.
5. After all residue has been removed, polish the entire glass
surface using the ceramic glass cleaner and paper towel.
Cleaning Metal Marks and Scratches
Metal marks and scratches from pans usually can be removed.
Be careful when placing pans onto the glass surface. To avoid
metal marks and scratches, do not slide pans across the glass
surface.
1. Turn off the unit, unplug power cord, and allow unit to cool.
2. Spread a few drops of ceramic glass cleaner onto the
marked area.
3. Using an appropriate cleaning wipe, rub the marked area
while applying pressure as needed.
4. If metal marks and scratches remain, repeat the steps
above as needed.
NOTE: Check the bottom of all pans for roughness that could
scratch the glass surface.
NOTE: Damage caused by sugary/sticky spills or rough pan
bottoms is not covered under warranty.
15
MAINTENANCE
CAUTION