Peg-Perego ypsi Instrucciones De Uso página 25

fastening and unfastening the seat.
4 REMOVING THE YPSI SEAT FROM THE CHASSIS: To
unfasten the Ypsi Seat, press the levers near the
chassis attachments (fig_a) and lift the seat at the
same time (fig_b).
5 ASSEMBLING THE PADS: attach the side pads' Velcro
straps to the seat's pad.
Turn over the reducers from the front.
Reducers attached correctly.
6 Open the buckles by pressing on the extremities and
detach (Fig. a). Open the abduction belt as shown to
make it easier to position the reducer (Fig.b).
7 Position the reducer into the seat leaving the
abduction belt on top of it (Fig.a).
Slip the Velcro strap through the seat eyelet (Fig.b)
and complete the attachment process by making the
Velcro stick under the seat. Close both buckles (Fig.c).
8 Attach both black pads, including the abduction belt
between them (Fig.a), attach both Velcro straps under
the seat pad (Fig.b) and fasten the press-stud button
(Fig.c).
9 Complete by fastening the buttons of the seat's side
pads (Fig.a) on both sides. Pads installed correctly.
10 FRONT BAR: Attach the front bar in the slots as shown
(fig.a) until you hear a click.
The front bar can be removed by pressing the two
buttons at its extremities (fig_b), or opened on one
side by pressing only one of the two buttons (fig_c).
11 HOOD: To use the hood, pull it out completely until it
clicks into place.
12 The hood comes with a mesh insert so that the
child can be seen from any position. The hood can
be further expanded by unzipping it and pulling it
forward.
13 Slide the hood's attachments on the uprights (fig_a)
to change the distance between the hood and the
seat (fig_b).
14 BED POSITION: the seat can be adjusted in three
positions that range from "sitting" to "lying", with an
intermediate position (fig_a).
Before adjusting the seat to a flatter position, the
handlebar must be extended (Fig_b). You can switch
from one position to another by pulling the lever
shown in the picture (fig_c).
15 ADJUSTING THE DEPTH OF THE SEAT: by opening the
sack's side zip, the seat depth can be increased.
When increasing the depth, the seat's pad and the
side pads must be replaced with the larger ones
(accessory provided, figure 33).
16 ADJUSTING THE HEADREST: it can be adjusted in 3
positions. To adjust:
open the zip on the seat's backrest (Fig.a),
release both Velcro straps to remove it from the
backrest (Fig.b),
remove the headrest from the front (Fig. c),
reposition it by inserting the Velcro straps at the
desired height (Fig. d) and fixing them onto the
backrest. Close the zip.
17 USING AND ADJUSTING THE CONTAINMENT BELTS:
fasten the buckles until you hear a click. Adjust
their adherence to the child by pulling the strap
towards you (arrow 1). To open the buckles, press the
extremities as shown (arrow 2) and unfasten.
18 ADJUSTING THE CHEST BELT: it can be adjusted in 2
positions.
To adjust:
open the zip on the seat's backrest and unfasten the
two Velcro straps to remove them from the backrest
(Fig.a),
remove the pad from the front (Fig. b),
reposition it by inserting the Velcro straps at the
desired height (Fig. c) and fixing them onto the
backrest. Close the zip.
The pad will adhere more or less closely to the child
All manuals and user guides at all-guidesbox.com
19 ADJUSTING THE FOOTREST: the height can be
20 FOOT BELTS: To open the buckles, press the
21 ADJUSTING THE SEAT PAD:
- unbutton the side pads,
- unfasten the Velcro strap underneath the seat of the
- remove them and set them aside.
- position on the front seat the upper pad and fasten its
- the side pads with Velcro fasteners, under the upper
- attach the abduction belt's Velcro straps under the
22 FOLDING THE CHASSIS WITH THE YPSI SEAT ATTACHED:
- fold down the hood,
- close the footrest by pushing it inwards (fig. a),
- press the levers on the upright (fig.b) and fold the
23 WARNING: If the seat is mum-facing it cannot
24 OPENING THE CHASSIS WITH YPSI SEAT ATTACHED:
25 FOLDING THE CHASSIS WITH YPSI SEAT ATTACHED:
- 25 -
depending on how you position the Velcro fasteners.
adjusted as needed. Open the two zips at the front
(Fig.a). At the back of the footrest, unscrew the knobs
that loosen the footrest (Fig. b). Reposition it as
needed by moving it up or down (Fig.c). Once it is at
the desired height, screw on the knobs at the back to
fix the footrest. IMPORTANT: always close the two zips
(Fig.d).
When raising or lowering the footrest, it is advisable
to adjust the height of the seat pad in section 21.
extremities and unfasten (Fig a). There are adjustable
buckles underneath for greater adherence to the foot
(Fig b). To loosen the foot belt, adjust the buckles
(Arrow 1); to tighten the belt around the feet, pull as
shown by arrow 2.
there are 3 positions (Fig a).
Before adjusting it into the desired position:
upper pad,
Unfasten under the seat the two Velcro straps of the
abduction belt (Fig b)
from the front and extract it upwards (Fig c).
The abduction belt must be extracted and
repositioned at the same height chosen for the
seat; there are 3 available positions (fig.d).
Now you can reposition it.
Having repositioned the upper pad and the
abduction belt, reposition the other elements at the
same desired height:
Velcro strap under the seat (section 7b),
pad and the two side buttons to attach to the seat
(section 30b),
seat and button them up again from the front (section
30a).
the Ypsi Seat can be folded while still attached to the
chassis only if it is world-facing.
To do so:
Ypsi Seat on itself (fig.c).
be folded attached onto the chassis. It must be
unfastened (fig_a).
It can take up less room when folded (fig_b) .
Press the side attachment fastener downwards, grip
the upper ends of the handle bar and rotate them
towards you until the chassis opens completely
(fig_a). Ypsi chassis open (fig_b). A "click" sound
means it has opened correctly and corresponds to the
attachment onto the base. Next, open the Ypsi Seat
from the ends, pulling it until it clicks (fig_c).
put the front wheels in locked position (fig_a), lower
the handle bar to the lowest position (fig_b). Rotate
the safety lever to the left (fig_c) and, at the same
time, pull the frame's internal handle bar towards you
(fig_d).
Lift the handle bar until the frame is completely
folded (fig_e).
To fold correctly, check the side fastener is engaged. If
it has not engaged automatically, compress the frame
slightly. The folded stroller is free-standing .