Philips One HY1200 Manual Del Usuario página 3

Explanation of symbols
The following symbols may appear on the product:
- Read Operator's Manual (Fig. 2).
- Detachable Power Supply Part (Fig. 3): The
"xxxxxx" indicates the model number of the
approved chargers to be used.
Introduction
Congratulations on your purchase and welcome to
Philips! To fully benefit from the support that Philips
offers, register your product at
www.philips.com/welcome.
Intended use
Philips One power toothbrushes are intended to
remove adherent plaque and food debris from the
teeth to reduce tooth decay and improve and
maintain oral health. Philips One power toothbrushes
are intended for consumer home use. Use by children
should be with adult supervision.
Your Philips One (Fig. 1)
1 Handle
2 Power button
3 Battery light indicator
4 Charging port
Accessories:
5 Brush head(s)
6 Travel case
7 Travel case lid
8 Brush head travel cap
9 USB-A to small plug
Note: Accessories included may vary based on the
model purchased.
Getting started
Attaching the brush head
1 Align the brush head so the bristles point in the
same direction as the front of the handle. Press the
brush head down onto the metal shaft (Fig. 4).
Note: It is normal to see a slight gap between the
brush head and the handle (Fig. 5). This allows the
brush head to vibrate properly.
Charging your Philips One
1 Plug the USB-A charging cable into the charging
port at the bottom of the handle (Fig. 6).
2 Connect the USB-A charging cable into a 5V USB
wall adapter (Type A).
Note: Wall adapter not included. Only use 5V IPX-4
adapter (Type A).
3 Your Philips One beeps twice to indicate that the
toothbrush is charging.
4 Your toothbrush continues to charge until it is fully
charged.
- When the toothbrush is charging, the battery
indicator fades up and down in white.
- When fully charged, the battery indicator lights
up solid white and turns off after 30 seconds of
being fully charged.
Note: It can take up to 8 hours to fully charge the
battery, but you can use the toothbrush before it is
fully charged.
Travelling
Note: Depending on the model purchased, your
Philips One comes with a travel case or travel cap to
store your power toothbrush when travelling or
between uses.
Travel case
Put your Philips One toothbrush in the travel case with
the bristles facing downwards. Snap close the lid of
the travel case.
To remove your Philips One toothbrush in the travel
case, follow these steps:
1 Flip open the travel case lid.
2 While holding both ends of the travel case, pinch
the base of the toothbrush (Fig. 7).
3 The toothbrush will raise. Lift the toothbrush.
Brush head travel cap
Place your Philips One brush head inside the enclosure
of the brush head travel cap with bristles facing
upwards. Press the two sides of the cap together to
close (Fig. 8).
To remove the brush head travel cap:
1 Ensure the cap is facing upward and the handle is
facing you.
2 Hold each side of the cap with opposite hands,
pushing down on the right side of the cap while
using the other hand to gently open the left side
in the direction of the arrow (Fig. 9).
Using your Philips One toothbrush
If you are using this toothbrush for the first time, it is
normal to feel more vibration than when using a
manual toothbrush. The Philips One uses
microvibrations to help gently clean your teeth. Please
follow the brushing instructions below for the best
experience.
Philips One comes with a SmarTimer and QuadPacer
to help you brush evenly throughout your mouth.
SmarTimer
The SmarTimer indicates that your 2-minute brushing
cycle is complete by beeping 3 times and
automatically turning off.
Note: Dental professionals recommend brushing no
less than 2 minutes twice a day.
QuadPacer
The QuadPacer is an interval timer that beeps every
30 seconds to remind you to brush all teeth evenly by
dividing your mouth into 4 sections (Fig. 10).
Begin brushing in section 1 (outside upper teeth) and
brush for 30 seconds before you move to section 2
(inside upper teeth). Continue brushing in section 3
(outside lower teeth) and brush for 30 seconds before
you move to section 4 (inside lower teeth).
Note: If you press the power button after you started
the brushing cycle, the toothbrush will pause. After a
pause of 30 seconds, the SmarTimer and QuadPacer
reset.