Stanley SL227 Manual De Instrucciones página 24

ENGLISH
4. Screw the out flange (10) onto the spindle (7) (Fig. C3)
► the ring on the flange (10) must face towards
the disc when fitting a grinding disc (A)
► the ring on the flange (10) must face away
from the disc when fitting a cutting disc (B)
5. Press the spindle lock (2) and rotate the spindle (7)
until it locks in position (Fig. C2).
6. Tighten the flange (10) with the two-pin spanner
supplied.
7. Release the spindle lock.
8. To remove the disc, loosen the flange (10) with the
two-pin spanner.
Warning! Do not use a damaged disc.
MOUNTING THE SIDE HANDLE (Fig.D)
f For grinding, screw the side handle (4) tightly into
one of the holes (11) or (12) on either side of the gear
case.
PREPARATION BEFORE USE
f Attach the safety guard and appropriate abrasive or
grinding wheels. Do not use abrasive or grinding
wheels that are overly worn.
f Make sure that the inner and outer flanges are
attached correctly.
f Make sure that the abrasive or grinding wheels are
rotating in the direction of the arrows on the
accessories and tool.
OPERATION (Fig. F)
Instructions
Warning! Always observe the safety instructions and
applicable regulations.
Warning! To minimize the danger of serious
personal injury, please switch off the tool power and
disconnect all plugs before adjusting or removing/
installing any accessory. Before reassembling the tool,
press and release the trigger switch to make sure the tool
is already switched off.
Warning!
f Make sure all materials to be grinded are secured in
position.
f Apply slight pressure to the tool. Do not apply side
pressure to the abrasive disc.
f Avoid overloading. If the tool becomes hot, let it spin
for a few minutes with no load.
1. Be sure to hold the tool tightly with both hands (one
hand on housing, the other on side handle). Start the
tool and bring the grinding wheel on the work piece.
24
2. Keep the edge of the wheel tilted at angle from 15 to
30 degrees against the surface of the work piece.
3. When using a new grinding wheel, do not operate
the wheel in the B direction, otherwise, it will cut into
the work piece. When the edge of wheel has been
rounded off, you are free to operate the grinder in
either the A or B direction.
STARTING AND STOPPING (Fig. A)
Warning! Before using the tool, check whether the
handle is tightened securely. Check whether the ON/OFF
switch is working normally.
Before plugging in the tool to the power supply, check
whether the switch is in the OFF position when pressing
the rear end of the switch.
To start the tool, press the rear end of the switch and slide
it forward. Then press the front end of the switch to lock it.
Press the rear end of the switch to stop the tool.
Warning! Do not switch the tool on or off while under
load conditions.
PROPER HAND POSITION (Fig. G)
Warning! To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
Warning! To reduce the risk of serious personal injury,
ALWAYS hold securely in anticipation of a sudden reaction.
Proper hand position requires one hand on the side handle
(Fig. A), with the other hand on the body of the tool, as
shown in Fig. G.
SWITCHES
Caution! Hold the body of the tool firmly to maintain
control of the tool at start up and during use and until the
wheel or accessory stops rotating. Make sure the wheel
has come to a complete stop before laying the tool down.
Note: To reduce unexpected tool movement, do not switch
the tool on or off while under load conditions. Allow the
grinder to run up to full speed before touching the work
surface. Lift the tool from the surface before turning the
tool off. Allow the tool to stop rotating before putting it
down.
ON/OFF switch (1) with auto-lock(Fig. A)
Warning! Before connecting the tool to a power supply,
be sure the slider switch is in the off position by pressing
the front part of the switch and releasing. Ensure the
slider switch is in the off position as described above after
any interruption in power supply to the tool, such as the
activation of a ground fault interrupter, throwing of a circuit