Publicidad
Idiomas disponibles
Idiomas disponibles
Dear Customer,
In order for you to enjoy the many tech-
nical features of your new tapedack TG 29,
we recommend, that you read these in-
structions
carefully
before
you
operate
the unit for the first time.
Fold out page 3 and familiarize yourself
wiih all the operating features while stu-
dying the Instructions: We
are sure that
doing
so, no
recording
will fail and we
think, ft will be worth white the few minu-
tes you take to study the instructions.
Now
we
wish you
great enjoyment
with
your Dual TG 29.
The most Important technical features
@ 3 magnetic
tapeheads
for recording,
playback and erasing
@ 2 separate stereo amplifiers for racor-
ding and playback
@ On tape monitoring
© 2 tape speeds: 7!/2 ips. to meet the
most exacting standards; 31/4 ips. for
hifi recording quality of all recordings
@ Through
4-track system
double tape
use
@ Horizontal and vertical operation (TG
29 CV)
@ Push-button
operation
with security
locking to prevent accidental
erasing.
@ Drop-out
free
recordings
and
play-
backs by hyperbolic shaped tapeheads
@ Push-pull h. +. generator circuit
@ Electronically stabilized power supply
@ 2 Illuminated VU meters, calibrated In
ав
@ Pilot tight for recording operation
@ Tape brakes controlled by tension fee-
ling levers
provides
utmost
care
for
even the thinnest tapes
@ Separate level controls, operating in-
dependently or coupled
@ 2 inputs with
microphone
sensitivity
allows
mixing
of two
programs
on
monaural operation
© Multiplay (sound on sound) recordings,
switchable, may be checked directly
@ Switchable
control
between
source
(off-tape) and tape (on-tape) while re-
cording,
to get comparison
between
the orginal and the recording
@ Automatic tape-end stop by tension
feeling lever
© 4-digit index counter with instant-reset
button
@ Quick-stop button
@ Synchronizable with slides- and film
projectors
Connection to power line
Before you operate your Dual TG
29 for
the first time, please check your local line
voltage and make sure, it corresponds to
the voltage selector @ on your unit. Nor-
mally the unit Is shipped set at 220 V,
50 Hz ог 117 V, 60 Hz.
Voltage can be selected to 110, 130, 220
or 250 Y а. с. by turning the voltage selec-
tor on the rear of the unit. Change of ope-
rating voltage does not require a change
of fuses.
To change a defective fuse, first press the
cap,
then
turn
it counterclockwise
and
take it out together with the fuse.
Use only F 400 mA fuses and be sure to
disconnect the line plug before touching
the voltage
adjustment, replacing fuses or
opening the
unit.
Adjusting the unit to a different
line frequency
The adjustment is done by replacing the
motor pulleys.
1. Remove
the knobs and after removing
the six screws, also the top-cover plate,
then release the belt.
2. Remove
the sink screw,
replace
both
the small and the large motor pulley
and fasten the sink screw again.
o
. Put the belt in place again and fasten
top
cover
plate
with the six screws.
Finally set the knobs.
Motor pulley pair for 50 Hz =
part no.
214595
Motor
pulley pair for 60 Hz
=
part no.
214 596
Stereo amplifier or radlo hook-up
Your TG 29 can be connected
to a play-
back amplifier with an audio cable. Con-
nect RADIO output jack with tape input
jack of the amplifier or the radio. With this
done the unit Is ready for recorded tapes
playback
operation
as
well
as
for any
690%
г
® ©
composition of programs originating from
the units
which
are
connected
to the
amplifier
(tuner or recordplayer).
H your
amplifier is equipped with a separate
„monitor"
input
jack
and
a
„monitor"
switch then the „monitor"
jacks of both
the tapedeck and the amplifier have to be
connected also with an audio cable.
If your
unit is equipped
with
RCA-type
Jacks (input 1 =
left channel, input 2 =
right channel}
connect
output 1 of tape-
deck to input 1 of amplifier and output 2
to input 2 with a RCA-type plug cable.
Publicidad
