Publicidad
Idiomas disponibles
Idiomas disponibles
10) EMG SET 2
Allows to determine the emergency channel 2.
Press the CH knob (6) for 4 seconds to enter MENU.
1.
Turn the rotary CH knob (6) or use the UP/DN buttons (6) on the
microphone to select the menu {EMG 2}. "EMG" blinks.
-
Repeat points 2 to 7 from EMG SET 1 to set the emergency channel
2
Emergency channel 2 default is 19 AM.
See the § EMG on page 10.
11) PA SETTING
This function allows to
select
Address.
Press the CH knob (6) for 4 seconds to enter MENU.
1.
Turn the rotary CH knob (6) or use the UP/DN buttons (6) on the
microphone to select the menu {PA SET}.
2.
Press the CH knob (6) to confirm. The current value blinks in the
display.
3.
Turn the rotary CH knob (6) or use the UP/DN buttons (6) on the
microphone to select the PA operating mode: PA, I n or oF.
4a. Short press the CH knob (6) again to validate your choice and
stay in the MENU.
4b. Long press (1s) the CH knob (6) again to validate your choice
and exit the MENU.
disappears from the display.
5.
If no key is pressed, the unit exits MENU after 10 seconds.
appears from the display.
-
PA: the modulation of the microphone and the received signal
are transmitted to the Public Address loudspeaker connected
to jack PA.SP. (D). "PA" flashes alternately with the modulation
mode used: AM, FM, LSB or SSB.
-
I n: the modulation of the microphone is transmitted to external
loudspeaker connected to jack PA.SP. (D). The received signal
is transmitted to the internal loudspeaker [or external optional
loudspeaker connected to jack EXT.SP (C)]."PA" flashes alternately
with the modulation mode used: AM, FM, LSB ou SSB.
appears.
the operating mode of PA, Public
appears.
-
OF: The reception is no more functional. Only the modulation of
the microphone is transmitted to the Public Address loudspeaker
connected to jack PA.SP. (D). "PA" is displayed, channels are
replaced by PA.
PA
mode, press PTT switch to display "PA LEVEL". Then turn the
In
rotary CH knob (6) to adjust the audio level of the PA.
PA setting default is: PA.
See the § PA (Public Address) on page 8.
12) RESET
Press the CH knob (6) for 4 seconds to enter MENU.
1.
Turn the rotary CH knob (6) or use the UP/DN buttons (6) on the
microphone to select the menu {RESET}.
2.
Press the CH knob (6) to confirm. The current value blinks in the
display.
3.
Turn the rotary CH knob (6) or use the UP/DN buttons (6) on the
microphone to select the RESET function. SC (Scan Skip) or AL
(ALL).
4.
Short press the CH knob (6) again to confirm your choice.
A last verification is asked. "no" blinks on the display.
5.
Turn the rotary CH knob (6) or use the UP/DN buttons (6) on the
microphone to select "
6.
Short press the CH knob (6) again to validate your choice and
exit the MENU.
7.
If no key is pressed, the unit exits MENU after 10 seconds.
dis-
appears from the display.
SC reset all the channels stored with the SKIP function (see the §
SKIP on page 9).
AL reset all user-defined settings and returns to default values.
E) TECHNICAL CHARACTERISTICS
1)
GENERAL
- Channels
- Modulation modes
- Frequency ranges
15
appears.
".
: 40
: AM / FM / LSB / USB
: from 26.965 MHz to 27.405 MHz
dis-
Publicidad
