Publicidad
Idiomas disponibles
Idiomas disponibles
Remove the battery pack before starting any work on the
appliance.
WARNING! To reduce the risk of fire, personal injury, and
product damage due to a short circuit, never immerse
your device, battery pack or charger in fluid or allow a
fluid to flow inside them. Corrosive or conductive fluids,
such as seawater, certain industrial chemicals, and bleach
or bleach containing products, etc., Can cause a short
circuit.
Use only System Typ LI 22 / LBC202Z-2 chargers for
charging System CGB20/JLH262102000G battery packs.
Never break open battery packs and chargers and store
only in dry rooms. Keep dry at all times.
Prior to commissioning, check the following points on the
pole-mounted pruner:
- Correct position of shoulder strap and inspection of the
quick release mechanism
- Damage to the device like cracks on the guide rail
- Correct guide rail seating
- Installation/running direction of the problem-free
(sharp) saw chain
- Saw chain tension (in case of a new chain, check and
readjust this multiple times)
- Functioning chain lubrication
Check the automatic chain lubrication
Installing the shoulder strap
1.
Position the shoulder strap so that the strap is over
the left shoulder (Chapter II).
2.
Attach the snap hook to the shaft bracket on the
shaft (Chapter II).
Position the shoulder strap so that the strap is over the
left shoulder (Chapter II).
Attach the snap hook to the shaft bracket on the shaft
(Chapter II).
Never carry the belt diagonally across your shoulders and
chest, but rather only on one shoulder, so that you can
rapidly move away from the tool in case of danger.
Regularly check the function of the automatic chain
lubrication to prevent overheating and associated
damage to the blade and saw chain. To do this, point
the tip of the sword against a smooth surface (board,
section of a tree) and let the chainsaw run. If an increasing
amount of oil becomes visible during this procedure, the
automatic chain lubrication is working properly.
WARNING! Danger of injury!
If the shoulder strap is not detached promptly in an
emergency, serious injuries can result.
WARNING
Keep your working position in mind to ensure safe
working. Do not use the pole-mounted pruner from
a ladder or other unsafe position. Ensure that you
have firm footing and use appropriate protective
clothing. Do not be tempted to make ill-considered
cuts. This can endanger yourself and others.
Cutting springpoles
A springpole is any log, branch, rooted stump, or sapling
which is bent under tension by other wood so that it
springs back if the wood holding it is cut or removed.
On a fallen tree, a rooted stump has a high potential of
springing back to the upright position during the bucking
cut to separate the log from the stump. Watch out for
springpoles—they are dangerous.
WARNING
Springpoles are dangerous and could strike the
operator, causing the operator to lose control of the
chain saw. This could result in severe or fatal injury
to the operator. This should be done by trained
users.
Some regions have regulations that restrict the use of the
machine. Check with your local authority for advice.
Never allow children or people unfamiliar with the
instructions to use the machine. Local regulations may
restrict the age of the operator.
Ensure before each use that all controls and safety
devices function correctly. Do not use the machine if the
"off" switch does not stop the motor.
Do not wear loose fitting clothing, short trousers, or
jewellery of any kind.
Secure long hair so it is above shoulder level to prevent
entanglement in moving parts.
Beware of thrown, flying, or falling objects. Keep all
bystanders, children, and animals at least 15 m away from
the work area.
Do not operate in poor lighting. The operator requires a
clear view of the work area to identify potential hazards.
Use of hearing protection reduces the ability to hear
warnings (shouts or alarms). The operator must pay extra
attention to what is going on in the work area.
Operating similar tools nearby increases both the risk
of hearing injury and the potential for other persons to
enter your work area.
Keep firm footing and balance. Do not overreach.
Overreaching can result in loss of balance and can
increase the risk of kickback.
Keep all parts of your body away from any moving part.
Inspect the chain saw before each use. Check for correct
operation of all controls, including the chain brake. Check
for loose fasteners, make sure all guards and handles are
properly and securely attached. Replace any damaged
parts before use.
Do not modify the machine in any way or use parts
and accessories which are not recommended by the
manufacturer.
EN
ENGLISH
27
Publicidad
