Descargar Imprimir esta página

LiftMaster JDC Manual Del Usuario página 44

Publicidad

Idiomas disponibles

Idiomas disponibles

Auxiliary Relays Accessory Kit (AUXREL)
Configure the Relay Adapter
This operator allows for the programming of a single mid-stop door position.
1
2
3
To set the open mid-stop position:
OFF
OFF
1.
In Programming Mode, go to Door Position => Open Mid-Stop or
Close Mid-Stop.
OFF
ON
ON
OFF
2.
Use the Up/Down buttons to move the door to the desired position.
3.
Select Save = Enter
ON
ON
To erase the mid-stop, select Erase Open Mid-Stop or Erase Close-Mid
Stop option, then select Save=Enter.
OFF
OFF
NOTE: Restoring defaults or resetting limits will erase the mid-stop position.
AUXILIARY RELAYS
ON
OFF
Aux Relay Switches: Set the AUX RELAY switches as needed to
obtain the desired function as shown below.
OFF
ON
J6 Input: Communicator bus connects control board, expansion
board, or relay adapter board.
ON
ON
J7 Input: Communicator bus connects control board, expansion
board, or relay adapter board.
RED/GREEN LIGHT FUNCTIONALITY
AUX24: Supplies +24Vdc up to 1AMP to wired accessories.
Red light wired to AUX RELAY 1. Green light wired to AUX RELAY 2.
AUX RELAY 1 SWITCHES
1 OFF
Red light wired to AUX RELAY 1. Green light wired to AUX RELAY 2.
Closed
DOOR STATE
Opening
Open
Closing
Closed
Opening
Open
seconds
Closing
seconds
Defined Mid Stop
Undefined Mid Stop
Timer more than 5
seconds
Timer less than 5
seconds
* For red light ON when gate is closed, set switch 1 on AUX RELAY 1 to ON.
4.
AUX RELAY 1
Relay always off. Use this Aux Relay setting to conserve battery power.
Energizes at open limit. Use with SAMS (Sequenced Access Management System, jointly with barrier gate).
Energizes when not at close limit. For an additional audible or visual display, connect an external light (low voltage).
Energizes when motor is on (gate in motion). For an additional audible or visual display, connect an external buzzer or light
voltage).
Energizes 3 seconds before gate motion and remains energized
during gate motion. The onboard alarm will sound. For an
additional audible or visual display, connect an external buzzer or
light (low voltage).
Energizes when AC power or solar power is present. There is
approximately a 10-12 second delay before relay cutoff, after AC
shutdown.
Energizes if gate is manually tampered with by being pushed off of close limit. For an additional audible or visual display, co
external buzzer or light (low voltage).
The 1, 2, and 3 LEDs will blink out the cycle count (cycle count is
stored on the control board). See below.
RED/GREEN LIGHT FUNCTIONALITY
2 OFF
3 OFF
Red light OFF*
AUX RELAY 1 SWITCHES
Red light ON/Flash
Red light OFF
1 OFF
2 OFF
Red light ON/Flash
Red light OFF*
n/a
Red light ON
Red light ON/Flash
Red light OFF
Red light OFF
Red light ON/Flash
Red light ON/Flash
N/A
Red light ON
Red light OFF
Red light ON/Flash
AUX RELAY 2 SWITCHES
1 ON
2 ON
3 ON
Green light OFF
AUX RELAY 2 SWITCHES
Green light OFF
Green light ON
3 OFF
1 ON
2 ON
Green light OFF
Green light OFF
n/a
Green light OFF
Green light OFF
Green light ON
Green light ON
Green light OFF
Green light OFF
N/A
RELAY 1
to ON
Green light OFF
Green light ON
Green light OFF
44
RELAY ADAPTER BOARD
Energizes 3 seconds before gate motion and remains e
during gate motion. For an additional audible or visual
connect an external buzzer or light (low voltage).
Energizes when on battery power. There is approximate
second delay before relay cutoff, after AC shutdown.
Red/green light functionality, see below.
3 ON
N.O.
Com
N.C.
RELAY ADAPTER BOARD
AUX RELAY 2
N.C.
Com
N.O.

Publicidad

loading