Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
Folded
Fig. 27
The scooter must be switched off before folding.
1.
Hold the handlebar stem, turn it counterclockwise to open the safety hook and lift the
quick release lever.
2.
Align the bell and hook and engage. When opened, unhook the bell lever from the
mudguard hook.
3.
Unfold the handlebar stem, lock the quick release lever and rotate the handle bar
clockwise to close the safety hook.
Carrying
Hold the handlebar stem with one or both hands.
Adjusting the handlebar
Fig. 28
1.
Inner hexagon nut
2.
Hexagonal bolt
3.
Hexagon nut
Prolonged use of the scooter can cause the screws to loosen and the handlebar stem to
become unstable. If you notice that the handlebar stem wobbles when riding, follow the
steps below.
Tools
I: 8-10 mm spanner II: 4 mm Allen key
Note: These tools must be in the user's possession.
Steps
1.
With the scooter folded, use tool I to loosen "c" (clockwise).
2.
Use tool I to loosen "b" (clockwise).
3.
Use tool II to adjust "a" (clockwise) to the proper position, and use tool I to tighten "b"
(counterclockwise).
4.
Lift the handlebar, close the quick release lever and turn the handlebar clockwise to
close the safety hook.
5.
Shake the handlebar stem to see if the problem has been resolved. If not, repeat steps 2
and 3.
6.
If resolved, continue to step 6.
7.
Fold the scooter again and use tool I to tighten "c" (counterclockwise).
* Step 6 is mandatory.
64
ORIGINAL MANUAL TRANSLATION
5. CLEANING AND MAINTENANCE
-
Make sure the device is not plugged to the power supply or switched on before cleaning
or maintenance.
-
Use a soft cloth to clean the exterior housing of the electric scooter.
-
Never use alcohol, petrol, paraffin, corrosive, or abrasive products to clean the electric
scooter.
-
Never immerse the electric scooter in water or any other liquid to clean it, as this could
damage the electronic parts permanently.
-
Never use pressurised water to clean the electric scooter.
-
Do not try to repair the electric scooter on your own. Should it not work correctly or be
damaged, please contact the official Cecotec Technical Support Service.
-
Self-tapping nuts and other fasteners may loosen their hold and need to be retightened.
-
If the scooter is expected to be inactive for more than 30 days, fully charge the battery
and place it in a cool, dry place. Remember to recharge it every 60 days to protect the
battery from possible damage beyond the scope of the warranty.
-
Disassembly of the wheels is complicated and improper assembly can cause instability
and malfunction.
Brake disc
You must check the brake discs are in perfect condition, matching the brake calliper: fix this
easily with the Allen key provided. Brake pads are consumable parts and must be replaced
when their shelf life expires.
Storage
-
When not in use, store the scooter in a dry and ventilated place. Do not leave it outdoors
for a long time. Excessive sunlight, overheating, and overcooling accelerate tyre ageing
and compromise the service life of the scooter and its battery.
-
Charge it only if the room temperature is between 0 °C and 35 °C and store it at a
temperature between -10 °C and 45 °C.
Battery release
-
Removing the battery is complicated and may alter the operation of the electric scooter:
you can contact an authorised repair entity if the warranty is still valid. If the warranty
has expired, you can contact a specialist workshop of your choice. You can also contact
the Cecotec Customer Service Department.
-
For proper removal of the battery for subsequent recycling, you must:
1.
Remove the anti-slip rubber from the top of the scooter.
2.
Loosen the screws on the upper part of the scooter.
3.
Remove the screws from the plastic side protectors.
4.
Remove these protectors.
ENGLISH
BONGO SERIE M40 XL CONNECTED
65
Publicidad
