Metabo MAG 32 Manual Original página 16

17026972_0610 MAG 32 MAG 50.book Seite 16 Dienstag, 15. Juni 2010 4:55 16
ENGLISH
ENG
Always use sharp tools in perfect condition.
Switch off the machine. Pull the mains plug
from the socket. Caution! When you unplug
the mains plug, the magnet loses its holding
power.
Tools with a taper shank MK2 can be used directly
in the female taper of the drill spindle (11).
Driving out the tool:
Insert the removal tool (10) - with the sloping edge
against the tool - in the slot (9) on the machine
neck. If the removal tool cannot be inserted
through the drill spindle, you should turn the drill
spindle (11) slightly by hand. Drive out the tool by
knocking lightly on the removal tool with a
hammer. (10)
Special notes on tools with
Weldon shank 19 mm:
For MAG 50: First insert the industrial attachment
6.26602 (see chapter 10 Accessories).
When inserting the attachment, ensure that
the side pin of the industrial attachment
engages with the anti-twist device (23).
Then connect the hose from the cooling lubrica-
tion unit to the connecting piece on the industrial
attachment 6.26602.
Inserting the tool:
- Insert the centring pin (of an appropriate length)
into the tool.
- Insert the tool in the tool holder (22) so that both
surfaces (on the cylindrical part of the tool) are
located at the positions of the threaded pins (21).
- Guide the tool upwards as far as it will go
(against the pressure of the integral spring) and
tighten the threaded pins (21) using the Allen key.
Removing the tool:
- Release the two threaded pins (21).
8 Cleaning, Maintenance
Perform regular maintenance work, cleaning and
lubrication.
Remove the mains plug from the socket before
carrying out any settings, maintenance or repairs.
Caution! When you unplug the mains plug, the
magnet loses its holding power.
For lubricating the rack and pinion that moves the
slide plate (14) up and down, a few drops of oil
should be applied occasionally to the rack.
Coat the sliding surfaces of the slide plate (14) with
multi-purpose grease.
Backlash of the slide plate
The backlash of the side plate is set ex works.
16
The side plate (14) must be adjusted so that it can
still be moved freely up and down (when the
driving unit is installed), and so that it will remain in
any position without the weight of the driving unit
pulling it down.
If necessary, you can adjust the backlash of the
slide plate (14) using the three threaded pins (7):
release the counternuts, tighten the threaded pins
and fasten the counternuts again.
9 Troubleshooting
Electronic restart protection (for preventing
accidental restarting)
If, when the driving unit is switched on,
a) the magnet is switched off or
b) the power supply is interrupted,
the driving unit comes to a standstill.
If the magnet is then reactivated or the power
supply restored, the driving unit will not restart
automatically for safety reasons (electronic restart
protection). Switch on the driving unit again at the
switch (16) .
See also chapter 7.4.
Electronic signal indicator (13) for MAG 50
Continuously lit - Overload
The motor temperature is too high. Reduce the
load on the machine. The machine will stop if the
overloading persists. Switch off the machine,
switch it back on again and allow to cool down at
idle speed.
10 Accessories
Use only genuine Metabo accessories.
If you need any accessories, check with your
dealer.
The dealer needs to know the exact model of your
power tool in order to select the correct accessory.
See page 4.
A Core drill with 19 mm Weldon shank, HSS/HM
B Centring pin, short,
HSS: for 30 mm cutting depth
HM: for core drill bit diameter 14-17 mm
C Centring pin, long,
HSS: for 55 mm cutting depth
HM: for core drill bit diameter 18-100 mm
D Morse taper for chuck with female taper
E Key-type chuck with female taper
F Metal drill bit
G Quick replacement system MK2 on Weldon,
19 mm
H Industrial holder MK2 on Weldon, 19 mm
I Securing belt with ratchet