Astralpool Combo 22439 Manual De Instrucciones Y Funcionamiento página 6

•
Check that both the filter and the pump's pre-filter covers are properly closed. Open the suction valve
•
Place the selector valve in the BACKWASH position (fig. 17) (p. 38).
•
Place the timer switch in position I (fig. 21) or the speed selector in the manual position (fig. 15) (p. 73).
Place the pump protection switch of the control panel in position I (connection) (fig. 21) (p. 74).
•
Wash the sand (see section 6) (p. 7).
•
To turn the equipment off, place the pump switch in the OFF position (disconnection) (fig. 15) (p. 73).
•
Put the selector valve in the FILTER position (fig. 17) (p. 73).
PROGRAMMING THE TIMER-PROGRAMMER
•
The control panel has a timer-programmer to automate filtering times, start-up and shutdown of the equipment.
To programme this function, follow these steps (this may vary depending on the timer model):
•
Make sure that the pump switch is in the OFF position (disconnection) (fig. 21) (p. 74).
•
To set the time: remove the transparent cover from the timer. Turn the inside dial of the timer in a clockwise
direction until the current time is lined up with the arrow (triangle) on the base (fig. 22) (p. 74).
•
To set the operation time: the timer has 48 tabs, each of which is equivalent to half an hour. The tabs can be
raised (off) or pressed (on). Set the operation time by pressing the required tabs (fig. 23) (p. 74). Setting a
daily filtering time of 8 hours (16 tabs) is recommended.
•
To start-up automatic operation: The timer-programmer has a two position (I or II) switch. Position I starts the
manual operation of the pump. On the other hand, position II allows the timer tabs to control the on or off
function of the pump (fig. 20) (p. 74). NOTE: do not force the timer trigger when putting it into position II, as if
the activated timer tab is pressed, the trigger will move to position I.
•
Replace the transparent cover on the timer.
5. OPERATION
•
Never stand on the cover of the filtration box or the front module.
•
The cover of the filtration box should ALWAYS be closed with lock and key.
•
Do not allow children or adults to handle or sit on the equipment.
•
Never use the front module as a diving board to dive into the pool.
•
Never use the front module as a support for getting out of the pool.
•
Keep the space for the skimmer (where the basket is located) free of objects.
•
Keep the skimmer baskets and the pre-filter of the pump clean.
OPERATION: WATER FILTERING
The skimmer is the filtering element which collects water from the surface. The water passes through the skimmer
basket. The larger particles remain trapped in the basket, and the impurities which cannot be retained pass through
to the cartridge filter where they are filtered. For the water filtering operation, follow these steps:
•
Place the pump switch in the OFF position (disconnection) (fig. 21) (p. 74).
•
Place the selector valve in the filter position and the three-way valve in the skimmer position. (fig. 17) (p. 73).
•
To programme an automatic timed filtering operation, set the programmer as described in the "Programming the
timer" section of this manual. If you wish to start-up the filtering operation manually, place the timer switch in
position I (fig. 20) (p. 74) and turn on the pump by placing the switch in the ON position (connection) (fig. 21)
(p. 74).
•
To stop the filtering operation, place the pump switch in the OFF position (disconnection) (fig. 21) (p. 74). If you
wish to leave the pump in the automatic timed filtering position, leave the pump switch in the ON position (fig.
21) (p. 74) and the timer trigger in position II, without forcing it (fig. 20) (p. 74).
OPERATION: SWIMMING POOL LIGHTING
The compact filtration unit is fitted with an underwater light to illuminate the swimming pool. To turn it on or off,
simply press the pneumatic switch of the light located at the back of the filtration box (fig. 13) (p. 73).The light is
designed to be totally submerged in freshwater swimming pools. It is a class III electrical apparatus with a very low
safety voltage (12 V with alternate current). The light meets the IPX8 protection standard (resistant to the
penetration of dust, solid bodies and moisture) with a nominal immersion depth of 2 m.
The light meets international lighting safety standards, particularly standard EN 60598-2-18. LUMINAIRES PART 2:
PARTICULAR REQUIREMENTS SECTION 18 LUMINAIRES FOR SWIMMING POOLS AND SIMILAR
APPLICATIONS.
6 of 80
22439E0200-03