Milwaukee M18 SMS216 Manual Original página 17

Adapt the feed speed to avoid overheating the blade tips and to avoid
melting plastic materials during cutting.
The insertion tool is sharp-edged and can become hot during use.
WARNING! Danger of cuts and burns
- when handling the insertion tools
- when setting the device down.
Wear protective gloves when handling insertion tools.
Even when the product is used as prescribed, it is still impossible to
completely eliminate certain residual risk factors. The following ha-
zards may arise in use and the operator should pay special attention
to avoid the following:
• Impairment of hearing, restrict exposure and wear appropriate
hearing protection.
• Health hazards caused by breathing dust developed when sawing
wood, wear a mask if necessary.
LASER
Do not stare into beam. Do not point laser light at other persons.
Do not view directly into beam with optical instruments (binocular,
GB
telescope).
Do not point laser at reflective surfaces,
Avoid exposure to laser radiation. Laser may emit hazardous
radiation.
Do not replace the installed laser with a different type. Any repairs
must only be carried out by the authorized service agent.
SPECIFIED CONDITIONS OF USE
The mitre saw can be used for sawing solid wood, bonded wood,
glued veneer, materials similar to wood, and plastics.
Stock having a round or irregular cross section (such as firewood) must
not be cut, as it can not be securely held during cutting. When sawing
thin stock layed on edge, a suitable auxilary fence must be used for
firm support.
RESIDUAL RISK
Even when the product is used as prescribed, it is still impossible to
completely eliminate certain residual risk factors. The following ha-
zards may arise in use and the operator should pay special attention
to avoid the following:
• Injury caused by vibration. Hold the product by designated
handles and restrict working time and exposure.
• Exposure to noise can cause hearing injury. Wear ear protection
and limit exposure.
• Injury due to flying debris. Wear eye protection, heavy long
trousers and substancial footwear at all times.
• Inhalation of toxic dusts.
English
28 28
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product described
under "Technical Data" fulfills all the relevant provisions of the
directives
2011/65/EU, (EU) 2015/863 (RoHS)
2006/42/EC
2014/30/EU
and the following harmonized standards have been used.
EN 62841-1:2015+A11:2022
EN IEC 62841-3-9:2020+A11:2020
EN IEC 55014-1:2021
EN IEC 55014-2:2021
EN IEC 63000:2018
Winnenden, 2022-12-12
Alexander Krug / Managing Director
Authorized to compile the technical file
Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany
GB-DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole responsibility that
the product described under „Technical Data" fulfills all the relevant
provisions of the following Regulations
S.I. 2012/3032 (as amended), S.I. 2008/1597 (as amended),
S.I. 2016/1091 (as amended) and that the following designated
standards have been used:
BS EN 62841-1:2015+A11:2022
BS EN IEC 62841-3-9:2020+A11:2020
BS EN IEC 55014-1:2021
BS EN IEC 55014-2:2021
BS EN IEC 63000:2018
Winnenden, 2022-12-12
Alexander Krug / Managing Director
Authorized to compile the technical file
Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany
BATTERIES
Battery packs which have not been used for some time should be
recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance of the
battery pack. Avoid extended exposure to heat or sunshine (risk of
overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, the battery packs have to be fully charged,
after use.
To obtain the longest possible battery life remove the battery pack from
the charger once it is fully charged.
For battery pack storage longer than 30 days: Store the battery pack
where the temperature is below 27°C and away from moisture Store the
battery packs in a 30% - 50% charged condition
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods Legislation
requirements.
Transportation of those batteries has to be done in accordance with local,
national and international provisions and regulations.
The user can transport the batteries by road without further requirements.
Commercial transport of Lithium-Ion batteries by third parties is subject
to Dangerous Goods regulations. Transport preparation and transport
are exclusively to be carried out by appropriately trained persons and the
process has to be accompanied by corresponding experts.
When transporting batteries:
Ensure that battery contact terminals are protected and insulated to pre-
vent short circuit. Ensure that battery pack is secured against movement
within packaging. Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice
BATTERY PACK PROTECTION
In extremely high torque, binding, stalling and short circuit situations that
cause high current draw, the tool will stop for about 2 seconds and then
the tool will turn OFF. To reset, remove the battery pack from the tool and
replace it.
Under extreme circumstances, the internal temperature of the battery
pack could raise too much. If this happens, the fuel gauge will flash until
the battery pack cooled down. After the lights go off, the work may
continue.
Place the battery on the charger to charge and reset it.
MAINTENANCE
Remove the battery pack before starting any work on the appliance.
Be sure to disconnect the tool from the power supply before attaching or
removing the saw blade.
Replace the table insert when worn
Clean tool and guarding system with dry cloth.
The ventilation slots of the machine must be kept clear at all times.
Use only Milwaukee accessories and Milwaukee spare parts. Should
components need to be replaced which have not been described, please
contact one of our Milwaukee service agents (see our list of guarantee/
service addresses).
If needed, an exploded view of the tool can be ordered. Please state the
Article No. as well as the machine type printed on the label and order the
drawing at your local service agents or directly at: Techtronic Industries
GmbH, Max-Eyth-Straße 10,
71364 Winnenden, Germany.
SYMBOLS
CAUTION! WARNING! DANGER!
Remove the battery pack before starting any work on the
appliance.
Please read the instructions carefully before starting the
machine.
Always wear goggles when using the machine.
Wear ear protectors!
Wear gloves!
Always keep hands away from the path of the saw blade.
Never expose tool to rain.
This product contains a class 2 consumer
laser product acc. to
EN 60825-1:2014+A11:2021 and EN 50689:2021.
Do not stare into beam!
Do not dispose of waste batteries, waste electrical and
electronic equipment as unsorted municipal waste. Waste
batteries and waste electrical and electronic equipment
must be collected separately.
Waste batteries, waste accumulators and light sources
have to be removed from equipment.
Check with your local authority or retailer for recycling
advice and collection point.
According to local regulations retailers may have an obliga-
tion to take back waste batteries and Waste electrical and
electronic equipment free of charge.
Your contribution to re-use and recycling of waste batteries
and waste electrical and electronic equipment helps to
reduce the demand of raw materials.
Waste batteries, in particular containing lithium and waste
Electrical and electronic equipment contain valuable,
recyclable materials, which can adversely impact the
environment and the human health, if not disposed of in
an environmentally compatible manner.
Delete personal data from waste equipment, if any.
V
Voltage
Direct Current
n
No-load speed
0
Saw blade dia. x hole dia
European Conformity Mark
British Conformity Mark
Ukraine Conformity Mark
EurAsian Conformity Mark
English
29 29
GB