Sirius SLTR75 2013 Instrucciones De Uso Y De Montaje página 13

INSTALLATION
*Before installing the appliance, make sure
that none of the parts is damaged in any way.
In case of damaged parts, contact your retai-
ler and do not proceed with installation.
Read all of the following instructions carefully
before installing the appliance:
- Use an air outlet pipe of the shortest pos-
sible length.
- Limit the number of pipe elbows.
- Use a material approved by standards and
regulations.
- Avoid any sudden changes in the pipe sec-
tion (recommended constant diameter: Ø 150
mm or equal surface area).
-The manufacturer shall not respond for air
capacity or noise problems due to non- com-
pliance with above mentioned instructions,
and no warranty shall be given.
All the models have been designed in order to
have the possibility of directing the air out-
let in the rear side of the appliance ; if you
chose to use this function, it is necessary to
remove the no. 10 screws of the sucking unit
support (fig. 3 ), take out the sucking unit and
rotate it in such a way to direct the air out-let
nozzle towards the rear side of the applian-
ce (fig. 4); then place the sucking unit in its
seat again and tighten the screws previously
removed.
By using its drilling template (fig. 5A), drill
the holes for the wall bracket installation;
Appliances shall be installed at a minimum
distance of 400mm from the cook-top.
Assure a distance of 480mm from the cook-
top with SL90 and SL91 models.
Fix the brackets to the wall, by using the
screw anchors and screws supplied with the
product;
Hang the body (Fig. 6) to the wall brackets
previously fixed.
Install no. 4 fixing screws on the correspon-
ding holes on the upper side of the appliance
(fig.7). Tighten the front screw (fig.7A) to as-
sure the appliance to the wall, then check if
the hood is perfectly leveled. If it isn't leveled
deal tighting the back screws (fig.7B): to the
right one to raise the right side of the hood
or the left screw to raise the left side.
Perform the electric connection.
SLTR75, SLTC75 MODEL ONLY
Activate the glass panel lifting up, as shown
in the 'Working' section; when the panel is
completely open, which is done by setting the
IV speed, remove the grid as shown in (fig.
8), then remove the grease filters and make
sure the hood is securely fixed to the wall, by
using the inside screws (fig. 9).
Reinsert the grease filters, the grid and close
the front panel by setting the OFF function, as
shown in the 'Working' section.
In External motor version:
Connect the external motor's cable to the
terminal board found in side the plastic box
of the wiring . Make sure to respect the colors
of cables when perfor ming the electrical con-
nection (fig.18).
SL90 SL91 MODELS ONLY
Open the front panel by rotating the lower
side upwards, as shown in (fig. 10), then re-
move the grease filter.
Fix the appliance to the wall with the screws
provided, as per (fig. 11).
Reinsert the grease filter and close the front
panel.
Sucking version – upper outlet
Fix the pipe bearing bracket to the wall and/
or ceiling by using the anchor screws and
screws provided (fig. 12), centred to the
hood.
Connect the motor air-outlet flange to the
exhaust hole, by using a suitable pipe.
Place the two ornamental pipes on the hood
body; lift the internal pipe up until it reaches
the ceiling; then fix it to the pipe bearing bra-
cket, by using the two self-threaded screws
provided.
Sucking version - back outlet
Install the air outlet grill above the hood in
the relative seat (refer to Fig. 13). The stain-
less steel chimneys are not necessary.
Filtering version
Install the air outlet grill above the hood in
the relative seat (refer to Fig. 13). The stain-
less steel chimneys are not necessary.
In case that the appliance is used in the fil-
tering version mode, it is necessary to install
the charcoal filters. First remove the metal
grease-filter, as indicated for each model in
the MAINTENANCE part, then place the char-
coal filter in his seat just behind the grease-
filter.
13