Silvercrest SDBK 2400 E1 Guía Rápida página 19

˜ Before first use
Remove the packaging . Check if all parts are complete .
o
To remove any production or transport residue, iron a
o
simple scrap of fabric (e .g . a cloth or rag) before first use .
NOTE: The product may give off some vapours or odours
during first use . These are production or transport residue
that will quickly subside . There may also be quiet noises
such as clicking or crackling . These will also quickly
subside once the plastic parts have finally adjusted to the
operating conditions .
˜ Operation
˜ Setting the temperature
The pointer behind the temperature control
o
current temperature setting .
Turn the temperature control
o
setting MIN to the desired temperature level .
The temperature control
o
are general recommendations for different types of fabric:
Symbol Setting
Low temperature
For synthetic fabrics (e .g . nylon)
Medium temperature
For sensitive fabrics (e .g . silk or wool)
High temperature
For tough fabrics (e .g . cotton or linen)
Highest temperature
For steam ironing
˜ Ironing
m
ATTENTION! Before ironing, check the ironing
instructions on the fabric or article of clothing . They are
usually included on a sewn-on tag .
m
ATTENTION! Operate the product on an even and solid
surface .
NOTES:
The product can be operated cordless . This makes the
o
product a little lighter . The power cord
the way during ironing .
As soon as the product is placed on the stand base
o
the soleplate is heating up . The temperature control
[ 14 ]
lamp lights up until the set temperature is reached .
6 ] [
1 . Turn the temperature control
way to MIN .
2 . Connect the power plug
outlet .
3 . Make sure the power cord
shows the
[ 11 ]
clockwise from the lowest
11 ] [
is divided into 3 ranges . They
11 ] [
is no longer in
[ 8 ]
10 ] [
counter-clockwise all the
[ 11 ]
with an appropriate power
[ 8 ]
is laid out safely .
[ 8 ]
4 . Set the temperature control
Temperature control lamp
On Product has not yet reached the set
temperature and is still heating up .
Off The set temperature has been reached .
5 . Once the set temperature has been reached, you can
begin ironing .
Cordless ironing
NOTE: The arrows on the product
base must be aligned .
10 ] [
1 . Place the product on the stand base
2 . Wait until the temperature control lamp
3 . The arrows and
closed (Fig . C) . Slide the stand base lock
the product upwards .
4 . Start ironing .
5 . To heat up the product again, place it on the stand
base .
[ 10 ]
NOTE: The product is only firmly locked to the stand
base when the arrows on the product
[ 10 ]
stand base are aligned .
Ironing with power cord
1 . Place the product on the stand base
and are aligned (Fig . C) .
2 . Wait until the temperature control lamp
3 . Once the set temperature has been reached, you can
start ironing .
NOTE: If you want to iron with many steam bursts
in quick succession, ironing with the power cord
is recommended . Otherwise the temperature of the
soleplate may fall below the set temperature faster
14 ] [
than normal as a result of too many steam bursts .
˜ Filling the water tank
m
DANGER! Risk of electric shock! Always disconnect
the power plug
8 ] [
water tank .
m
ATTENTION! Fill the water tank with tap water or
distilled water without any additives . If your tap water is
hard, use distilled water . Where the water is moderately
hard, mix distilled water and tap water at a ratio of 1:1 .
m
ATTENTION! Use the measuring cup
into the water tank .
,
NOTE: The water tank has a filling capacity of
approximately 320 ml .
NOTE: The max mark
filling capacity applies when the product is set up
vertically on the stand base
1 . Tip the product forward at approximately 45° .
2 . Open the lid of the fill opening
to the desired temperature .
11 ] [
[ 6 ]
and on the stand
.
[ 10 ]
goes out .
[ 6 ]
are aligned when the product is
to
[ 9 ]
and on the
. Make sure
10 ] [
goes out .
6 ] [
8 ] [
from the power outlet before filling the
to fill water
[ 15 ]
that marks the maximum
[ 13 ]
.
[ 10 ]
.
[ 2 ]
GB/IE
and lift
19