Triton TWX7 Instrucciones De Uso Y De Seguridad página 5

Note: If the power supply is interrupted during use, the machine will not restart. The ON/OFF Switch
will need to be activated again to resume operation.
User position & feed direction
• The main user position is defined by the location of the 'Knee-Off' Stop Button (11)
• ALWAYS remain in close proximity to the switch to instantly switch the machine off in the event of
an emergency
• Feed your workpieces from this position, in the direction indicated by the arrows on the table
surface of the individual module
Using the clamping holes
• The clamping table module features a series of 19mm diameter holes for the use of clamping
devices, and bench dogs
Using the table extensions (available as accessories)
• The outfeed and side support bars can be adjusted to provide sturdy support to larger workpieces.
Adjustability can be performed by loosening the Outfeed Support Knobs (15), and/or the Side
Support Knobs (4) and extending the corresponding support bar to the size of the workpiece
Accessories
• A full range of Workcentre accessories and compatible Triton power tools, including Circular Saws
and Precision Plunge Routers, is available from your Triton stockist. Spares can be obtained from
toolsparesonline.com
Maintenance
WARNING: ALWAYS disconnect the Workcentre from the power supply, before cleaning,
changing accessories, making adjustments or carrying out maintenance.
WARNING: ALWAYS wear protective equipment including eye protection and suitable, cut-proof
gloves when cleaning or carrying out maintenance.
General inspection
• Regularly check that all the fixing screws are tight. They may vibrate loose over time
• Inspect the supply cord of the tool, prior to each use, for damage or wear. Repairs should be
carried out by an authorised Triton service centre. This advice also applies to extension cords used
with this tool, as well as cords of the power tools installed in this Workcentre
Cleaning
• Keep your tool clean at all times. Dirt and dust will cause internal parts to wear quickly, and
shorten the device's service life
• Clean the body of your machine with a soft brush, or dry cloth
Troubleshooting for Clamping Table
Problem
Table module is not level
'Play' between table module and chassis
Guarantee
To register your guarantee visit our web site at
tritontools.com* and enter your details.
Purchase Record
Date of Purchase: ___ / ___ / ____
Model: TWX7
Retain your receipt as proof of purchase.
Australian Warranty Information
You may wish to register your product at www.tritontools.com but you are not under any
obligation to do so.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law.
You are entitled to a replacement or refund for a major failure and for compensation for any
other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or
replaced if the goods fail to be of acceptable quality and the failure does not amount to a major
failure.
This product is guaranteed against faulty materials and workmanship for 3 YEARS from the date
of purchase. Please retain your receipt as proof of purchase.
This warranty does not cover defects caused by or resulting from:
• (a) misuse, abuse or neglect;
• (b) trade, professional or hire use;
• (c) repairs attempted by anyone other than our authorised repair centres; or
• (d) damage caused by foreign objects, substances or accident.
Possible Cause
Levelling screws are not correctly adjusted
Rough surface
Legs not correctly seated
Module levelling bobbins, not correctly
adjusted
• Never use caustic agents to clean plastic parts. If dry cleaning is not sufficient, a mild detergent on
a damp cloth is recommended
• Water must never come into contact with the tool
• Ensure the tool is thoroughly dry before using it
• If available, use clean, dry, compressed air to blow through the ventilation holes (where
applicable)
Lubrication
• Lubricate all moving parts with PTFE spray at regular intervals, especially after heavy use or
cleaning
WARNING: DO NOT lubricate with oil or silicone-based maintenance sprays. Lubricant residue
will combine with wood and dust leading to dirt build-up interfering with moving parts and
mechanisms. ONLY dry lubricate, using PTFE spray.
Storage
• Store this tool carefully in a secure, dry place out of the reach of children
Contact – UK/EU
For technical or repair service advice, please contact the helpline on (+44) 1935 382 222
Web: www.tritontools.com
UK Address: Toolstream Ltd., Boundary Way, Lufton Trading Estate, Yeovil, Somerset, BA22 8HZ,
United Kingdom
EU Address: Toolstream B.V., Holtum-Noordweg 11, Unit 4, 6121 RE Born, The Netherlands
Contact – US
For technical or repair service advice, please contact the helpline (toll free) on: 855-227-3478
Web: www.tritontools.com
Address: Toolstream Inc., Triton Products, 380 Crompton St., Charlotte, NC 28273
Disposal
Always adhere to national regulations when disposing of power tools that are no longer functional
and are not viable for repair.
• Do not dispose of power tools or other waste electrical and electronic equipment (WEEE), with
household waste
• Contact your local waste disposal authority for information on the correct way to dispose of power
tools
Solution
Using a spirit level, adjust the Module Levelling Screws (25) till the surface module is flat
Ensure the Workcentre is situated on a secure flat surface. Relocate the table if the ground is found to be rough
Follow instructions provided under 'Initial set-up' , and ensure the legs are correctly seated and locked into
place
Adjust Module Levelling Bobbin Screw (27) to remove 'play' in Workcentre module
Triton Precision Power Tools guarantees to the purchaser of this product that if any part
proves to be defective due to faulty materials or workmanship within 3 YEARS from the
date of original purchase, Triton will repair, or at its discretion replace, the faulty part free
of charge.
This guarantee does not apply to commercial use nor does it extend to normal wear and
tear or damage as a result of accident, abuse or misuse.
* Register online within 30 days.
Terms & conditions apply.
This does not affect your statutory rights
Warranty Exclusions
Wearing parts, consumable items or service-related parts required when performing normal and
regular maintenance of this product are not covered by the warranty unless it is found to
be defective by an Authorised Service Centre.
Distributed in Australia by Carbatec:
Carbatec Pty Ltd, 128 Ingleston Rd, Wakerley QLD 4154
Enquiries
Email: callcentre@carbatec.com.au
Freecall number: 1800 658 111
The Carbatec policy is one of continuous improvement and the company reserves the right to alter
designs, colours and specifications without notice.
EN
6