Sabo 50-PRO E S VARIO Manual Del Operador página 52

EN
Excessive mowing speed
Mower paths
overlap sufficiently
Lawn matted
Cutting height too low and
Ejection blocked
grass too high.
Excessive mowing speed
Grass is wet
The cutter bar is blunt
The mulched grass
looks bad:
lumps, excessive
amounts of cut Mulching rule not followed
(cut max. 1/3 of grass
grass, coarse cut
height; the grass height to
be cut must be less than 10
cm).
Excessive travel speed
Grass accumulation under
the mower
Mower paths
overlap sufficiently
Grass is wet
In case of faults and defects which have not been listed here, please contact the
nearest authorised workshop.
Repairs which require specialised knowledge should only be performed by a
qualified expert. Your authorised workshop will naturally also be glad to help if you
do not wish to perform the maintenance work described here yourself.
21 MOTOR UNIT FAULT INDICATOR (FIGURE A2)
Light signal Meaning
The motor unit is in good
Green LED lights
working order.
up
The motor unit has
Orange LED lights
overheated.
up
Battery pack is drained.
Red LED flashes
Blade motor overloaded.
Orange LED
flashes
Communication between
Red and green
battery and control board
LEDs flash
disrupted
alternately
Adapt mowing speed.
do not With high grass, the mowing
paths may possibly have to
overlap more.
A noticeable improvement
can be achieved by using a
scarifier.
Set a higher cutting height
Adapt mowing speed.
Let lawn dry.
Have it resharpened and
balanced by an authorised
workshop.
Set a higher cutting height I.
Adapt travel speed.
Set a higher cutting height I.
do not With high grass, the mowing
paths may possibly have to
overlap more.
Set a higher cutting height I.
Let lawn dry.
Fixing the fault
Not necessary.
Check and clean the air
filters W + W1.
Let the mower cool down.
Reduce the load and do not
use the motor unit when the
ambient temperature is high.
Let the mower cool down.
Charge the battery.
Clean grass from the cutting
space / ejection canal,
remove blockages (remove
the battery/batteries first N2
!).
Set a higher cutting height
When mowing on a slope:
reduce the travel speed or
switch off autodrive. Mow at
right angles to the slope, not
upwards.
Check that the battery is
positioned correctly, or that
the batteries are correctly
placed in the battery
compartment. Correct this if
necessary and restart the
motor.
Have it checked by an
authorised workshop.
22 TECHNICAL DATA
Motor
Motor
Motor speed
Rated power
I.
Charger
See the separate operating instructions for the charger.
Permitted temperature range during charging
Battery
See the separate operating instructions for the battery.
Recommended temperature range for storage
Mower
Housing
Cutting width
Cutting heights
Height adjustable guide bar
Weight Machine with empty collecting bag
Also with 2 x 56 V 12 Ah batteries
Travel speed
Length
Width
Height
Wheels front / rear
Bearing front
Bearing rear
Permitted temperature range during use
Permitted temperature range for storage
Maximum permitted humidity
Sound power level
Sound power level;
measured according to DIN EN IEC 62841-4-3
Measuring inaccuracies; according to DIN EN ISO 4871
Guaranteed sound power level;
measured according to 2000/14/EC
Sound pressure level
Emission sound pressure level at operator's workplace;
I.
measured according to DIN EN IEC 62841-4-3
Measuring inaccuracies; according to DIN EN ISO 4871
Vibrations
The stated total vibration value has been measured according to a standardised
test procedure and can be used to compare the device with another machine. This
value can be used for a preliminary estimation of the vibration load.
Vibrations at the guide bar;
measured according to DIN EN IEC 62841-4-3
Measuring inaccuracies; according to DIN EN 12096
15
ECO
TURBO
ECO
TURBO
Die-cast aluminium with
25, 28, 35, 45, 55, 70, 80
ECO
TURBO
Ø 210 mm / Ø 210 mm
Bronze slide bearing
70 %, non-condensing
56 V DC motor
2400 rpm
2800 rpm
1.70 kW
2.40 kW
+ 5 to + 40 °C
+ 10 to + 26 °C
steel core
500 mm
Single wheel,
mm
3 times
45.0 kg
52.3 kg
2.5 – 4.1 km/h
2.9 – 4.8 km/h
1580 mm
755 mm
1100 mm
Needle bearing
0 to + 45 °C
- 5 to + 60 °C
L = 90.5 dB(A)
WA
1.4 dB
L = 92 dB(A)
wa
L = 77 dB(A)
pA
3 dB
a = 0.80 m/s
2
hW
0.40 m/s
2