Publicidad
Safety
Signs, symbols and instructions placed on this product must never be covered or removed and must
remain present and clearly legible throughout the entire lifetime of the product. Immediately replace or
repair illegible or damaged signs, symbols and instructions. Contact your local dealer for instructions.
Any adverse event in relation to the device must be reported to your local dealer and the national
competent authority in a timely manner. The local dealer will forward information to manufacturer
Caregiver
• Read the user manual carefully before use
and keep it for future reference. Incorrect use
of this product may cause serious injury to
the user.
• Always use the correct lifting techniques and
aids for this purpose.
• Never leave the user unattended in this
product. Ensure permanent supervision by a
caregiver.
• Repair/replacements must only be made
using new original R82 spare parts and
fittings and carried out in accordance with the
guidelines and service intervals prescribed by
the supplier.
• Settings and adjustments to the product or
accessories are only to be made by persons
who have read the user manual.
• If there is any doubt as to the continued safe
use of your R82 product or if any parts should
fail, stop using the product immediately and
contact your local dealer as soon as possible.
• When adjusting the seat angle, keep a hand
on the seat mounted on the frame to ensure
slow angling.
• Ensure that moving parts do not squeeze or
trap body parts when adjusting them.
• Ensure that body parts are not trapped
in openings for mounting of supports/
accessories.
• Always use the product in a moderate pace.
Do not run with the product.
• Information about transportation can be found
in the document "M1470 Transportation in
Motor Vehicles" supplied with the product.
• Information about roadability can be found in
the document "M1450 Roadability" supplied
with the product.
• Information regarding frame and seat
combinations including max. load in
combination can be found at: etac.com.
• This product contains small parts which could
present a choking hazard if removed from
their intended placing.
Environment
• Observe the surface temperature on the
product, before placing a user in it. This goes
especially for users with insensitive skin
as they cannot feel the heat. If the surface
temperature is above 41°C then allow the
product to cool before use.
• Use this product on a level surface without
EN
any obstacles. Be aware of reduced
maneuverability on slippery surfaces.
• When using on inclines, please refer to
measurements.
User
• If the user is close to the max. load limit
and/or has a lot of involuntary movements,
e.g. rocking, a larger size with a higher max.
load or a different R82 product should be
considered.
• Do not place more than one user in the
product.
• When changing user, clean the product and
disinfect it if necessary. Carry out necessary
adjustments after cleaning.
Product
• Removable parts without the use of a tool:
Rear wheels and most accessories. The
removal will have an adverse effect on the
device.
• Carry out all positional adjustments on the
product and accessories and ensure that
all knobs, screws and buckles are securely
fastened before use. Keep all tools out of the
reach of children.
• Activate the brakes before placing the user
into the product.
• Ensure the wheels are fully functional and
secure before use.
• The correct tyre pressure is printed on the
tyre casing and listed in the section for tyre
technical data.
• In case of a tyre puncture do not use the
product until remedied.
• Ensure the stability of the product is
maintained before placing the user in it.
• When the footplate is close to the floor and the
castors, the castors may be unable to swivel.
• Inspect the product and all of its accessories
and replace any worn out parts before use.
• Do not expose the gas damper to pressure or
high temperatures. DO NOT puncture.
• The product is approved for transportation
in vehicles according to ISO 7176-19. More
information can be found in the document
"M1470 Transportation in Motor Vehicles"
supplied with the product.
• In accordance with ISO 7176-19 annex D the
product is evaluated regarding the overall
rating of belt restraint accommodation.
Rating for: ease of properly positioning a three
50
.
etac.com
Publicidad
