Maytag BRAVOS Serie Manual De Uso Y Cuidado página 25

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Do you have an ENERGY STAR k qualified
washer?
The wash water temperatures
may feel cooler
to you than those of your previous
washer.
This is normal.
Does the wash water
temperature
feel lower than usual?
As washing
progresses,
the wash temperature
will decrease
slightly
for hot and warm
washes. [his
is normal.
lb reduce wrinkling,
the warm
rinse is regulated
to be cooler
than the warm wash.
Excessive sudsing
Did you use a non-HE detergent?
Regular or hand-washing
detergents
are not recommended
for this washer.
Use only High
Efficiency
("HE")
detergent.
Is there excessive
sudsing?
Always
measure
detergent.
Follow
detergent
manufacturer's
directions.
If you have very
soft water, you might
need to use less detergent.
Was the cycle interrupted
and then the Stain Cycle option
selected?
[he Stain Cycle
option
should
be started on a dry load only. [-he Stain Cycle
option
should
not be selected
after the tub has started filling
with water.
Cycle did not run Stain Cycle option
Did you select the Stain Cycle option?
[he Stain Cycle option
must be selected
for it to be included
in a wash cycle. The Stain
Cycle option
should
be started on a dry load only. Stain Cycle should
not be selected after
the tub has started filling
with water.
[he Stain Cycle option
is a default
in the Super Wash cycle and may be added to other
cycles.
Load
too
wet
Did you use the right cycle for the load being washed?
Select a higher
spin speed.
Did you use a cold rinse?
Cold rinses leave loads wetter than warm rinses. [his is normal.
Did you wash an extra
large load?
A large unbalanced
load could
result in a reduced
spin speed and wet clothes
at the end
of the cycle.
Evenly distribute
the load and make sure the height of the load does not
exceed
the top row of basket
holes.
Residue or lint on load
Did you add detergent
to the dispenser?
For best results,
use the dispenser
to dissolve
the detergent.
Did you sort properly?
Sort lint givers (towels,
chenille)
from lint takers (corduroy,
synthetics).
Also sort by color.
Did you overload
the washer?
[he wash load must be balanced
and not overloaded.
Clothes
should
move freely.
Lint or
powdered
detergent
can be trapped
in the load if the washer
is overloaded.
Wash smaller
loads. See "Starting
Your Washer"
for maximum
load size.
Did you use enough
detergent?
Follow
detergent
manufacturer's
directions.
Use enough
detergent
to hold the lint in the
water.
Did you line dry your clothing?
If so, you can expect
some lint on the clothing.
The air movement
and tumbling
of a dryer
removes
lint from the load.
Was paper or tissue left in pockets?
Is your
water
colder
than 60°F (15.6°C)?
....
Wash water colder
than 60°F (15.6°C)
may not completely
dissolve
the detergent.
Did you use the proper Soil Level and Wash Cycle
for the load?
Reducing
wash time (duration)
and wash speed are ways to reduce
lint.
Did you add detergent
to the dispenser?
For best results,
use the dispenser
to dissolve
the detergent.
Load is wrinkled,
twisted or tangled
Did you unload
the washer
promptly?
Unload
the washer
as soon as it stops.
Did you use the right
cycle for the load being washed?
[b reduce
wrinkling,
tangling
and twisting,
select a cycle with
low wash and spin speeds,
such as Delicate,
Handwash
or Wrinkle
Control.
Did you overload
the washer?
The wash load must be balanced
and not overloaded,
loads
should
move freely during
washing
to reduce
wrinkling,
tangling
and twisting.
Was the wash water
warm enough
to relax wrinkles?
If safe for the load, use warm or hot wash water. Use cold rinse water.
Are the hot and cold water
hoses reversed?
Check that the hot and cold water
hoses are connected
to the correct
faucets.
If the hot
and cold water inlet hoses are reversed, the washer will display
an "HC"
error code at the
end of the cycle. See "Connect
the Inlet Hoses."
A hot rinse followed
by spin will cause
wrinkling.
25

Publicidad

Tabla de contenido
loading

Tabla de contenido