Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
24 • ENGLISH
f Do-Be sure all blade and clamp washers are clean
and recessed sides of collars are against blade.
Tighten arbor screw securely.
f Do-Keep saw blade sharp.
f Do-Keep motor air slots free of chips and dirt.
f Do-Use blade guards at all times.
f Do-Keep hands out of path of saw blade.
f Do-Shut off power, disconnect cord from power
source and wait for saw blade to stop before servicing
or adjusting tool.
f Do-Support long work with an outboard tool rest.
f Do-Use only 10 inch diameter blades.
f Don't-Attempt to operate on anything but designated
voltage.
f Don't-Operate unless all clamp handles are tight.
f Don't-Use blades larger or smaller than those which
are recommended.
f Don't-Wedge anything against fan to hold motor shaft.
f Don't-Force cutting action.(Stalling or partial stalling of
motor can cause major damage. Allow motor to reach
full speed before cutting.)
f Don't-Cut ferrous metals (Those with any iron or steel
content) or any masonry.
f Don't-Use abrasive wheels. The excessive heat and
abrasive particles generated by them will damage
saw.
f Don't-Allow anyone to stand behind saw.
f Don't-Apply lubricants to the blade when it's running.
f Don't-Place either hand in the blade area when the
saw is connectedt o the power source.
f Don't-Use blades rated less than 5500R.P.M.
f Don't-Attempt to cut small pieces (hand within 6" of
blade) without clamping.
f Don't-Operate saw without guards in place.
f Don't-Perform any operation freehand.
f Don't-Reach around or behind saw blade.
f Don't-Place hands closer than 6 inches from the saw
blade.
f Don't-Reach underneath the saw unless it is turned off
and unplugged. The saw blade is exposed on the
underside of the saw.
f Don't-Move either hand from saw or workpiece or
raise arm until blade has stopped.
f Don't-Use without Kerf Plate or when kerf slot is wider
than 3/8"
f Don't-Carry saw by work extension or other accessory.
¡Caution! Some wood contains preservatives such
as copper chromium arsenate (CCA) which can be toxic.
When cutting these materials extra care should be taken
to avoid inhalation and minimize skin contact.
¡Caution! Use of this tool can generate dust containing
chemicals known to cause cancer, birth defects or other
reproductive harm. Use appropriate respiratory protection.
¡Caution! Do not connect unit to electrical power source
until complete instructions are read and understood.
FOR YOUR CONVENIENCE AND SAFETY, THE
FOLLOWING WARNING LABELS ARE ON YOUR
MITER SAW.
ON MOTOR HOUSING:
WARNING: For your own safety, read instruction manual
before operating saw. When servicing, use only
identical replacement parts. always wear eye protection.
ON FENCE: Clamp small pieces before cutting. see
manual.
ON GUARD:
DANGER: Keep away from blade
ON GUARD RETAINER PLATE "Properly secure bracket
with both screws before use."
ON TABLE: (2 Sitios).
Always tighten adjustment knobs before use. Keep
hands 6" from path of saw blade. Never perform
any operation freehand. Never cross arms in front
of blade. Think! You can prevent accidents. Do not
operate saw without guards in place. Never reach
in back of saw blade. always wear eye protection.
Shut off power and wait for blade to stop before
servicing, adjusting tool, or moving hands.
ELECTRICAL CONNECTION
Be sure your power supply agrees with the nameplate
marking. A voltage decrease of 10 percent or more will
cause a loss of power and overheating. All B&D tools are
factory tested. If this tool does not operate, check the
power supply.
CARACTERÍSTICAS (Fig. A y B)
1. Handle
2. Metal guard
3. Cutting Blade
4. Knob
5. Latch
6. Scale
7. Guide
8. Holes
9. Dust Exhaust
10. Safety Pin
11. Hand Indentations
12. Guide
13. Table
14. Motor
15. Switch
16. Cable
Publicidad
Tabla de contenido
