Specifications - Sony UP-897MD Manual De Instrucciones

Specifications

Power requirement
100 to 240 V AC, 50/60 Hz
Input current 1.5 A to 0.8 A
Operating temperature
5 °C to 35 °C (41 °F to 95 °F)
Operating humidity
20% to 80%
Operating pressure
700 hPa to 1,060 hPa
Storage and transport temperature
–20 °C to +60 °C (–4 °F to +140 °F)
Storage and transport humidity
20% to 80%
Storage and transport pressure
700 hPa to 1,060 hPa
154 × 88 × 240 mm (w/h/d)
Dimensions
(6 1/6 × 3 1/2 × 9 1/2 inches)
Mass 2.6 kg (5 lb 11 oz) (printer only)
Thermal head Thin-film thermal head, 1280 dots
Gradation 256-level gradation (8-bit)
Resolution (when "SC:WD1" is selected from "SCAN")
EIA: 1210 × 490 dots
CCIR: 1210 × 582 dots
Picture size (when "SC:WD1" or "SC:NOR" is selected
from "SCAN")
When "S:STD" is selected from
"SIDE"
EIA: 94 × 73 mm
CCIR: 94 × 71 mm
When "S:SIDE" is selected from
"SIDE"
EIA: 124 × 96 mm
CCIR: 127 × 96 mm
Printing speed About 2 sec./image (at standard
setting) (when "SP:HI" is selected
from "SPEED")
About 3.3 sec./image (at standard
setting) (when "SP:NOR" is
selected from "SPEED")
Picture memory 10 frames (800 k × 8 bits for one frame)
Input connector VIDEO IN (BNC type)
EIA or CCIR composite video signals
1.0 Vp-p, 75 ohms/high-impedance
(EIA/CCIR automatically
discriminated)
Output connector
VIDEO OUT (BNC type)
EIA or CCIR composite video signals
1.0 Vp-p, 75 ohm loop-through/EE
switchable
REMOTE connector (stereo mini jack)
1 GND
2 PRINT SIGNAL (TTL)
Input of LOW pulse over 100 msec.
initiates print.
3 PRINT BUSY (TTL)
Goes HIGH during printing
Accessories provided
Thermal head cleaning sheet (1)
Media label (1)
Operating Instructions (1)
Service Contact List (1)
Medical Specifications
Protection against electric shock:
Class I
Protection against harmful ingress of
water:
Ordinary
Degree of safety in the presence of a
flammable anesthetic mixture with
air or with oxygen or nitrous oxide:
Not suitable for use in the presence of
a flammable anesthetic mixture with
air or with oxygen or nitrous oxide
Mode of operation:
Continuous
The design and these specifications are subject to
change without prior notification.
Notes
• Always verify that the unit is operating properly before
use.
SONY WILL NOT BE LIABLE FOR DAMAGES OF
ANY KIND INCLUDING, BUT NOT LIMITED TO,
COMPENSATION OR REIMBURSEMENT ON
ACCOUNT OF FAILURE TO PRINT CONTENT OF
ANY TYPE OR LOSS OF DATA DUE TO FAILURE
OF THIS UNIT OR ITS PRINTING MEDIA,
ASSOCIATED SOFTWARE, EXTERNAL
STORAGE, OR OTHER EXTERNAL DEVICE.
• SONY WILL NOT BE LIABLE FOR DAMAGES OF
ANY KIND INCLUDING, BUT NOT LIMITED TO,
COMPENSATION OR REIMBURSEMENT ON
ACCOUNT OF THE LOSS OF PRESENT OR
PROSPECTIVE PROFITS DUE TO FAILURE OF
THIS UNIT, EITHER DURING THE WARRANTY
PERIOD OR AFTER EXPIRATION OF THE
WARRANTY, OR FOR ANY OTHER REASON
WHATSOEVER.
59
Specifications