Warranty; Troubleshooting Guide - DeWalt DW717 Manual De Instrucciones

useidentical replacement parts.
Three Year Limited Warranty
DEWALT will repair, without charge, any defects due to faulty
materials or workmanship for three years from the date of
purchase. This warranty does not cover part failure due to
normal wear or tool abuse. For further detail of warranty
coverage and warranty repair information, visit www.
dewalt.com or call 1-800-4-DEWALT (1-800-433-9258).
This warranty does not apply to accessories or damage
caused where repairs have been made or attempted by
others. This warranty gives you specific legal rights and
you may have other rights which vary in certain states or
provinces.
In addition to the warranty, DEWALT tools are covered by
our:
1 YEAR FREE SERVICE
DEWALT will maintain the tool and replace worn parts
caused by normal use, for free, any time during the first
year after purchase.
90 DAY MONEY BACK GUARANTEE
If you are not completely satisfied with the performance of
your DEWALT Power Tool, Laser, or Nailer for any reason,
you can return it within 90 days from the date of purchase
with a receipt for a full refund - no questions asked.
LATIN AMERICA: This warranty does not apply to products
sold in Latin America. For products sold in Latin America,
see country specific warranty information contained either
in the packaging, call the local company or see website for
warranty information.
FREE WARNING LABEL REPLACEMENT: If your
warning labels become illegible or are missing, call
1-800-4-DEWALT for a free replacement.
Patent Notification
Manufactured under one or more of the following U.S.
patents:
6,823,765 6,101,914 5,907,987 5,375,495
6,810,780 6,035,754 5,862,734 5,285,708
6,520,059, 6,032,563 5,582,089 5,199,343
Other patents may be pending.
Troubleshooting Guide
BE SURE TO FOLLOW SAFETY RULES AND INSTRUCTIONS
TROUBLE!
SAW WILL NOT START
WHAT'S WRONG? WHAT TO DO
Saw not piugged in Plug in saw
2. Fuse blown or circuit breaker 2. Replace fuse or reset circuit breaker
tripped
3. C0rd damaged 3 HaVe coid replaced bY auth0dzed set:
vice center
SAW MAKES
UNSATISFACTORY CUTS
4. Brushes worn out 4. Have brushes replaced by authorized
service center or replace them yourself
as instructed on Page 9.
1 Dull blade 1 Replace blade, see Page 61
2. Blade mounted backwards 2. Turn blade around, see Page 6.
31 Gum or pitch on blade 3. Remove b!ade and Clean with turpen-
tine and coarse steel wool or house_
hold oven cleaner
BLADE DOES NOT COME UP
TO SPEED
MACHINE VIBRATES
EXCESSIVELY
DOES NOT MAKE ACCURATE
MITER CUTS
MATERIAL PINCHES BLADE
4. Incorrect blade for work being done 4. Change the blade type, see pages 6.
Extension Cord to0 light or too long Replace with adequate Size Cord, see
Page 2.
2. Low house current 2. Contact your electric company
liSaw not mounted securely to stand 1! Tighten a!! mounting hardware, see
or work bench Page 6.
2. Stand or bench on uneven floor 2. Reposition on flat level surface, see
Page 6.
31 Damaged saw blade 31 Replace blade, see Page 61
1. Miter scale not adjusted correctly 1. Check and adjust, see Page 7.
2. Blade is n0t square tO fence 21 Check and adjustl see Page 81
3. Blade is not perpendicular to table 3. Check and adjust fence, see Page 8.
4, WorkPiece m0Ving 41 Clarnp workpiece securely fence or
glue 120 grit sandpaper to fence with
rubber cement.
1. Cutting bowed material
1. Position bowed material as shown on
Page 13.
15