Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
18
Preparatory work
Getting to know the appliance
Fig.
:
handle;
handheld release button;
1
1
2
handheld steam trigger (hidden);
3
dial;
water tank cap;
5
6
water tank;
power-on indicator;
8
9
handle of handheld steam cleaner;
11
jug (optional);
quick cord release hook;
13
floorhead release button;
15
hook
Accessories (optional):
Fig.
:
plastic brush;
24
1
brush;
utility head + pad;
4
nozzle;
extension hose;
7
Unpacking and assembling
Unpack the contents and check they are com-
1
plete. If you notice any transport damage or if any-
thing is missing, contact your dealer immediately.
Connect main body and floorhead (Fig.
2
Connect main body and handle. Grip the body
3
while connecting or removing the handle (Fig.
Stand steamer upright by pushing the main body
4
forward to lock into position (Fig.
Filling the water tank
!
WARNING!
Hot surface! Only refill the water tank when the
steamer is cooled down.
When steamer needs to be refilled during use,
1
switch steamer off and let it cool down.
handheld release button and disconnect handle
from the main body (Fig.
lease button and disconnect main body from floor-
head (Fig.
).
6
Place main body on flat surface.
4
tank cap anti clockwise and lift to remove (Fig.
Use measuring jug to fill the tank with 330 ml
6
(2 x 165 ml) of water (Fig.
cap and twist clockwise to tighten.
Connecting the appliance
Make sure the steamer is switched off.
1
cord completely from the quick cord release hooks
(Fig.
/
and
).
Insert the plug into a mains
1
13
16
3
socket.
Cleaning
!
WARNING!
Take extra care when cleaning on stairs.
steam control
4
floorhead;
carpetglider;
7
main body;
10
measuring
12
cord;
14
quick cord release
16
wire brush;
crevice
2
3
squeegee;
jet
5
6
2
).
).
3
4
).
Push
2
5
)
Push handheld re-
3
Twist water
5
).
7
).
Replace water tank
8
7
Unwind
2
EN
CAUTION!
Vacuum you carpets thoroughly and ensure hard
floor areas are free from grit and debris before
using the appliance.
NOTE:
The steamer will turn off if it overheats. Turn it off
and let it cool down for at least 2 to 4 hours.
Cleaning hard floors
CAUTION!
Never use the steamer without a microfibre pad
attached to the floorhead.
Place microfibre pad on the floor with the white
1
side facing up. Place floorhead on the microfibre pad
and make sure it covers the entire floorhead (Fig.
Insert plug into a mains socket.
2
control dial to 'ON' (Fig.
tor turns red. The steamer starts heating up and will
be ready after approx. 30 s.
dial to desired setting (Fig.
ed automatically.
5
and pull handle backwards (Fig.
er slowly forwards and backwards across the floor.
Turn steam control dial to 'OFF' . ➔ The steam-
7
er cools down, the power-on indicator goes out.
Unplug the plug from the mains socket.
steamer is cooled down hold corner of microfibre
pad down with your foot and lift steamer to peel
away.
Air-dry or wash microfibre pad.
10
Refreshing carpets
CAUTION!
Never use the appliance without a microfibre pad
attached to the floorhead. Only use carpetglider
when refreshing carpets.
See >"Cleaning hard floors" on page 17. Use carpet-
glider additionally:
Push floorhead with microfibre pad into the front
1
of the carpetglider, then place back of the floorhead
into the clip (Fig.
15
).
down place your foot on the clip of the carpetglider
and lift the steamer to remove.
Turn steam
3
). ➔ The power-on indica-
16
Twist steam control
4
). ➔ Steam jet is activat-
16
Place foot onto the floorhead
).
Move steam-
17
6
When
9
When steamer is cooled
2
).
14
8
Publicidad
Tabla de contenido
