Diamond Core Drills Safety Warnings - SPARKY BBK2 1500 Instrucciones De Uso

5. SERVICE
a) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
Diamond core drills safety
warnings
Wear ear protectors when operating the
machine. Exposure to noise can cause hearing
loss.
▪ Use the auxiliary handle supplied with the
machine. Loss of control can cause personal injury.
During operation provide eye protection
to prevent eyes from exposure to flying
particles. Wear goggles.
Take protective measures against inhalation
of dust. Some materials can contain toxic
ingredients. Wear a dust mask and work with
dust/chip extraction when connectable.
▪ Hold the power tool by insulated gripping
surfaces only, when performing an operation
where the cutting accessory may contact hidden
wiring or its own cord. Cutting accessory contacting
a "live" wire may make exposed metal parts of the
power tool "live" and could give the operator an
electric shock.
▪ Do not process materials containing asbestos.
Asbestos is considered carcinogenic.
WARNING: Before connecting a tool to a
power source be sure that the voltage supply is the
same as that specified on the nameplate of the tool.
▪ A power source with a voltage greater than that
specified for the tool can result in serious injury to the
user, as well as damage to the tool.
▪ If in doubt, do not plug in the tool.
▪ Using a power source with a voltage less than the
nameplate rating is harmful to the motor.
▪ Fully unwind cable drum extensions to avoid potential
overheating.
▪ When an extension cable is required, you must ensure
that it has the right ampere rating for your power tool
and it is in safe electrical condition.
WARNING: Always switch off and unplug
the power tool prior to any adjustment, servicing or
maintenance.
▪ While operating the machine, always hold it firmly
with both hands and provide for a secure stance. The
power tool is guided more securely with both hands.
▪ Always work standing on a stationary, secure and
level surface. Slippery or unstable surfaces like
ladders may lead to loss of balance or loss of control
of the tool.
Original instructions
▪ Be sure no one is below when using the tool in high
locations.
▪ Keep handles dry, clean, and free from oil and grease.
Greasy, oily handles are slippery causing loss of
control.
▪ Use non-skid safety footwear to avoid injuries
resulting from slipping on a smooth wet floor.
▪ Prior to operation use suitable detectors to determine
if utility lines are hidden in the work area or call the
local utility company for assistance. Contact of the
core bit with electric lines can lead to fire and electric
shock. Damaging a gas line can lead to explosion.
Penetrating a water line causes property damage or
may cause electric shock.
▪ Always keep the cord away from the working area
of the power tool. Never use the machine with a
damaged cable. Do not touch the damaged cable
and pull the mains plug when the cable is damaged
while operating. Damaged cables increase the risk of
electric shock.
▪ Prior to switching on the power tool ensure that the
core bit rotates freely.
▪ In case the core bit jams, switch the machine off
immediately.
▪ Do not touch the core bit or the machined surface
near the core bit during operation and immediately
after that; they may be extremely hot. You may get
serious burns.
▪ Keep work area clean. Blends of materials are
particularly dangerous. Dust from light alloys can burn
or explode.
▪ Rags, cloths, cord, string and the like should never be
left around the work area.
▪ Always switch the machine off before putting it down.
▪ The tool must be used only for its prescribed purpose.
Any use other than those mentioned in this Manual
will be considered a case of misuse. The user and not
the manufacturer shall be liable for any damage or
injury resulting from such cases of misuse.
▪ To use this tool properly, you must observe the safety
warnings, the general and operating instructions
found in this Manual. All persons who use and service
the machine have to be acquainted with this Manual
and must be informed about its potential hazards.
Children and frail people must not use this power tool.
Children should be supervised at all times if they are
in the area in which the tool is being used. It is also
imperative that you observe the accident prevention
regulations in force in your area. The same applies for
general rules of occupational health and safety.
▪ The manufacturer shall not be liable for any changes
made to the tool nor for any damage resulting from
such changes.
▪ Power tools must not be used outdoors in rainy
weather, or in moist environment (after rain) or in close
vicinity with easily flammable liquids and gases. The
working place should be well lit.
5
EN