Alliance Laundry Systems JT30XG Manual De Instalación, Operación, Mantenimiento Y Seguridad página 49

ELECTRICAL REQUIREMENTS
For 50 Pound Tumblers
NOTE: Minimum wire sizes are obtained from Canadian Electrical Code and are intended for use as a guideline
only. Electrical connections should be made only by a qualified electrical contractor in accordance with all
applicable local and national requirements.
NOTE:
DO NOT use aluminum wire
Heat Source Serial Plate Voltage
Gas & Steam 120V/60Hz/1ph
Gas & Steam 208 or 240V/60Hz/1ph
Gas & Steam 230-240V/50Hz/1ph
Gas & Steam 208 or 240V/60Hz/3ph
Gas & Steam 380 or 415V/50Hz/3ph
Gas & Steam 460-480V/60Hz/3ph
Electric 240V/50Hz/1ph
Electric 208V/60Hz/3ph
Electric 240V/60Hz/3ph
Electric 240V/50Hz/3ph
Electric 380V/50Hz/3ph
Electric 415V/60Hz/3ph
Electric 480V/60Hz/3ph
* Current Ratings vary slightly depending on model, see serial plate.
ELECTRICAL REQUIREMENTS
For 75 Pound Tumblers
NOTE: Minimum wire sizes are obtained from Canadian Electrical Code and are intended for use as a guideline
only. Electrical connections should be made only by a qualified electrical contractor in accordance with all
applicable local and national requirements.
NOTE: DO NOT use aluminum wire.
Heat Source Serial Plate Voltage
Gas & Steam 120V/60Hz/1ph
Gas & Steam 208 or 240V/60Hz/1ph
Gas & Steam 230-240V/50Hz/1ph
Gas & Steam 208 or 240V/60Hz/3ph
Gas & Steam 380 or 415V/50Hz/3ph
Gas & Steam 460-480V/60Hz/3ph
Electric 208V/60Hz/3ph
Electric 240V/60Hz/3ph
Electric 240V/50Hz/3ph
Electric 380V/50Hz/3ph
Electric 415V/60Hz/3ph
Electric 480V/60Hz/3ph
* Current Ratings vary slightly depending on model, see serial plate.
M414670
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
.
Terminal Block
Connections Required
L1, Neutral and ground
L1, L2, and ground
L1, Neutral and ground
L1, L2, L3, and ground
L1, L2, L3, and ground
L1, L2, L,3 and ground
L1, Neutral and ground
L1, L2, L3, and ground
L1, L2, L3, and ground
L1, L2, L3, and ground
L1, L2, L3, and ground
L1, L2, L3, and ground
L1, L2, L3, and ground
Table 11
Terminal Block
Connections Required
L1, Neutral and ground
L1, L2, and ground
L1, Neutral and ground
L1, L2, L3, and ground
L1, L2, L,3 and ground
L1, L2, L3, and ground
L1, L2, L3, and ground
L1, L2, L3, and ground
L1, L2, L3, and ground
L1, L2, L3, and ground
L1, L2, L3, and ground
L1, L2, L3, and ground
Table 12
Rated Breaker
Current Rating
* 20 Amps
* 15 Amps
* 15 Amps
* 15 Amps
* 15 Amps
* 15 Amps
91 Amps 100 Amps
88 Amps 100 Amps
78 Amps 90 Amps
78 Amps 90 Amps
50 Amps 60 Amps
46 Amps 60 Amps
38 Amps 50 Amps
Rated Breaker
Current Rating
* 20 Amps
* 15 Amps
* 15 Amps
* 15 Amps
* 15 Amps
* 15 Amps
88 Amps 100 Amps
78 Amps 90 Amps
78 Amps 90 Amps
50 Amps 60 Amps
46 Amps 60 Amps
38 Amps 50 Amps
Breaker Recommended
Poles Wire Size
1 12 AWG
2 14 AWG
1 14 AWG
3 14 AWG
3 14 AWG
3 14 AWG
1 2 AWG
3 2 AWG
3 2 AWG
3 2 AWG
3 4 AWG
3 4 AWG
3 6 AWG
Breaker Recommended
Poles Wire Size
1 12 AWG
2 14 AWG
1 14 AWG
3 14 AWG
3 14 AWG
3 14 AWG
3 2 AWG
3 2 AWG
3 2 AWG
3 4 AWG
3 4 AWG
3 6 AWG
47