Fein WPO10-25E Manual De Instrucciones página 18

OBJ_BUCH-0000000053-004.book Page 18 Monday, July 3, 2017 10:58 AM
en
18
Character Unit of measurement,
international
mm
kg
L dB
pA
L
dB
wA
L
dB
pCpeak
K...
2
m/s
2
m/s
h,P
2
m/s
h,DS
m, s, kg, A, mm, V,
W, Hz, N, °C, dB,
2
min, m/s
For your safety.
Read all safety warnings and all
WARNING
instructions. Failure to follow the
warnings and instructions may result in electric shock,
fire and/or serious injury.
Save all warnings and instructions for future reference.
Do not use this power tool before you have thor-
oughly read and completely understood this
Instruction Manual and the enclosed "General
Safety Instructions" (document number
3 41 30 054 06 1). The documents mentioned should be
kept for later use and enclosed with the power tool,
should it be passed on or sold.
Please also observe the relevant national industrial safety
regulations.
Intended use of the power tool:
Hand-guided polisher for dry polishing, sanding with
sanding sheets and brushing on surfaces of metal, stone,
plastic, wood, composite materials, paint/varnish, filler
and similar materials in weather-protected environments
with the application tools and accessories recommended
by FEIN.
This power tool is also suitable for use with AC genera-
tors with sufficient power output that correspond to the
Standard ISO 8528, design type G2. This Standard is par-
ticularly not complied with when the so-called distortion
factor exceeds 10 %. When in doubt, please refer to the
generator instruction/specification guide.
Safety warnings common for sanding with sanding
discs, working with wire brushes and polishing
This power tool is intended to function as a sander, wire
brush and polisher. Read all safety warnings, instruc-
tions, illustrations and specifications provided with this
power tool. Failure the follow all instructions listed below
may result in electric shock, fire and/or serious injury.
Operations such as grinding or cutting-off are not recom-
mended to be performed with this power tool. Operations
for which the power tool was not designed may create a
hazard and cause personal injury.
Unit of measurement, Explanation
national
mm M=Thread for clamping flange
l=Length of mounting thread
kg Weight according to EPTA-Procedure 01
dB Sound pressure level
dB Sound power level
dB Peak sound pressure level
Uncertainty
2
m/s Vibrational emission value according to
EN 60745 (vector sum of three directions)
2
m/s Mean vibrational value for polishing
2
m/s Mean vibrational value for sanding with sand-
ing sheet
m, s, kg, A, mm, V, Basic and derived units of measurement from
W, Hz, N, °C, dB, the international system of units SI.
2
min, m/s
Do not use accessories which are not specifically
designed and recommended by the tool manufacturer.
Just because the accessory can be attached to your power
tool, it does not assure safe operation.
The rated speed of the accessory must be at least equal
to the maximum speed marked on the power tool. Acces-
sories running faster than their rated speed can break and
fly apart.
The outside diameter and the thickness of your accessory
must be within the capacity rating of your power tool.
Incorrectly sized accessories cannot be adequately
guarded or controlled.
Threaded mounting of accessories must match the
grinder spindle thread. For accessories mounted by
flanges, the arbour hole of the accessory must fit the
locating diameter of the flange. Accessories that do not
match the mounting hardware of the power tool will run
out of balance, vibrate excessively and may cause loss of
control.
Do not use a damaged accessory. Before each use inspect
the accessory such as abrasive wheels for chips and
cracks, backing pad for cracks, tear or excess wear, wire
brush for loose or cracked wires. If power tool or acces-
sory is dropped, inspect for damage or install an undam-
aged accessory. After inspecting and installing an
accessory, position yourself and bystanders away from
the plane of the rotating accessory and run the power
tool at maximum no-load speed for one minute. Damaged
accessories will normally break apart during this testtime.
Wear personal protective equipment. Depending on appli-
cation, use face shield, safety goggles or safety glasses.
Where appropriate, wear dust mask, hearing protectors,
gloves and workshop apron capable of stopping small
abrasive or workpiece fragments. The eye protection
must be capable of stopping flying debris generated by
various operations. The dust mask or respirator must be
capable of filtrating particles generated by your opera-
tion. Prolonged exposure to high intensity noise may
cause hearing loss.