Power Stroke PS80519 Serie Manual Del Operador página 15

NOTE: This is a 4-cycle engine. DO NOT mix fuel and
lubricant together.
 Mix fuel stabilizer with gasoline according to fuel stabilizer
manufacturer's directions.
 Before removing the fuel cap, clean the area around it.
Remove the fuel cap.
 Insert a clean funnel into the fuel tank then slowly pour
gasoline into the tank. Fill tank to approximately 1-1/2 in.
below the top of the tank neck (this allows for fuel
expansion).
 Replace fuel cap and tighten until the cap "clicks".
 Clean up any spills before starting the engine.
STARTING AND STOPPING THE PRESSURE
WASHER
See Figures 13 - 14.
NOTICE:
Do not run the pressure washer without water supply
connected and turned on, as this may damage the high
pressure seals and decrease pump life. Completely
unwind the hose from its reel or coil and make sure the
hose is not being restricted by tires, rocks, or any other
objects that may lessen or prevent water flow to the
pressure washer.
Before starting the engine:
 Connect all hoses.
NOTE: Make sure the pressure washer's water intake
screen is in place and unclogged before connecting
garden hose.
 Check all fluids (lubricant and gas).
 Turn on the garden hose then pull the trigger to relieve air
pressure; hold the trigger until a steady stream of water
appears.
NOTE: Make sure the faucet is turned on fully and that
there are no kinks or leaks in the hose.
To start the engine:
 Turn the fuel valve to the OPEN position.
 Push choke to the START position.
NOTE: If restarting after a brief stop (i.e., after refueling
or moving), leave the choke lever in the RUN position.
 Grasp the starter grip and rope and pull slowly until
resistance is felt. Give the starter grip and rope a short,
brisk pull to start the engine.
NOTE: Do not allow the starter grip and rope to snap
back after starting; return it gently to its original place.
 Let engine run for 5 seconds, then pull choke to the RUN
position.
OPERATION
To stop the engine:
 Press and hold the OFF switch in the OFF ( O ) position
until the engine stops.
 Turn the fuel valve to the CLOSED position.
NOTE: Shutting OFF ( O ) the engine will not relieve pressure
in the system. Pull trigger to release water pressure.
WARNING:
While operating and storing, keep at least 3 feet of clear-
ance on all sides of this product, including overhead. Al-
low a minimum of 30 minutes of "cool down" time before
storage. Keep all body parts, clothing, combustible ma-
terials, and hoses away from the muffler. Heat created by
muffler and exhaust gases could be hot enough to cause
serious burns, ignite combustible objects, and/or damage
high pressure hoses that can result in an injection injury.
USING THE SPRAY WAND TRIGGER
See Figure 15.
For greater control and safety, keep both hands on the trigger
handle at all times.
 Pull back and hold the trigger to operate the pressure
washer.
 Release the trigger to stop the flow of water through the
nozzle.
To engage the lock out:
 Push up on the lock out until it clicks into the slot.
To disengage the lock out:
 Push the lock out down and into its original position.
To use the spray wand, start with the nozzle 1-2 ft. away
from the cleaning surface. Carefully approach the surface
just until the desired level of cleaning is achieved. If the spray
is too close it can damage the cleaning surface.
SELECTING THE RIGHT NOZZLE FOR THE JOB
See Figure 16.
Each of the nozzles has a different spray pattern. Before
starting any cleaning job, determine the best nozzle for the
job. Refer to the Nozzle Selection Guide for more informa-
tion about which nozzle to choose.
WARNING:
NEVER remove nozzles without first turning off the en-
gine, relieving the water pressure in the trigger handle,
and locking the lock out on the trigger handle. never point
the nozzle at your face or at others. The quick-connect
feature contains small springs that could eject the nozzle
with some force. Failure to follow these instructions could
result in an eye injury or other serious personal injury.
Page 11 — English