Automatic Mode; Switching Off - EdilKamin TINY Instalación Uso Y Mantenimiento

INSTRUCTIONS FOR USE
CONTINUED: Synoptic panel for the Kelly model

Automatic mode

•
Set the temperature which the room is to reach; the stove automatically adjusts the working power to reach it
(P3) or maintain it (P1).
If you set a lower temperature than current room temperature, the stove operates at P1 and consumes the corre-
sponding quantity of pellets.
Note on flame variability
Any variations in the state of the flame depend on the type of pellet used, the normal variability associated with solid
fuels and the periodic automatic combustion chamber cleaning (which does NOT replace the essential cold vacuum-
cleaning by the user before ignition).

Switching off

Hold the 0/1 key down for two seconds while the stove is operating. The shutdown procedure starts and the word "Off"
appears on the display (for a total of 10 minutes).
During shutdown:
• Pellet loading ceases.
• Ventilation turns up to maximum.
• The smoke expulsion motor turns up to maximum.
Never unplug the stove while it is shutting down.
WEEKLY TIME PROGRAMMER BUILT INTO PANEL
The concept of the weekly time programmer built into the central panel
It is possible to set 3 ignition programmes:
Pr 01 with settable on and off times;
Pr 02 with settable on and off times;
Pr 03 with settable on and off times.
It is possible to enable one or more of the three settings on each day of the week (day1 = Monday, day2 =
Tuesday...day7 = Sunday).
When on standby, the display alternates between showing the ignition mode (P1, P2, P3 or a temperature) and the
clock.
Setting the clock
Hold the MENU key down for about two seconds until tS appears. Press the MENU key three times until Prog appears.
Press the "-" key until SEt appears. Press the MENU key until the clock appears. It may be changed with the "-" key,
which decreases the time by one minute each time it is pressed, and with the "+" key, which increases it by 15 minutes
each time it is pressed. Once the time is set, confirm with the MENU key. The day number appears (day1=Monday,
day2=Tuesday... day7=Sunday), which can be changed with the "-" and "+" keys. Confirm with the MENU key.
Prog appears. Press the 0/1 key to quit clock setting.
Enabling programmes
Hold the MENU key down for about two seconds until tS appears. Press the MENU key three times until Prog appe-
ars. Press the "+" key until Pr OF appears. Press the MENU key until OFF appears. Press the "+ " or "-" key until ON
appears. Confirm with the MENU key. Prog appears. Press the O/1 key to return to standby. When the stove is in Pr
mode, it responds to programmed on and off times.
Setting a programme (e.g. Pr01)
Hold the MENU key down for about two seconds until tS appears. Press the MENU key three times until Prog appe-
ars. Press the "+" key twice until Pr1 appears. Press the MENU key until On P1 appears together with the "on time". It
may be changed with the "+" and "-" keys in ten-minute intervals. Press the MENU key to confirm. OfP1 appears
together with the off time. This may be changed with the "+" and "-" keys in ten-minute intervals. Press MENU to
confirm. "Of d1" appears (which means program 1 is not enabled on day 1, Monday). This may be changed into Ond1
(which means program 1 is enabled on day 1, Monday) using the "+" and "-" keys.
Press MENU to move on to the second day, and so on until day 7.
Press the MENU key again and Prog appears. To quit programming press the 0/1 key.
On and off times may be set for Pr 2 and Pr 3 in a similar way, and it can be decided which days they are enabled on.
50