Roland VK-77 Manual Del Usuario página 103

cc | H.Bar Feet
———————————+—————————————————————————————————————
46H (70) | 16'
47H (71) | 5-1/3'
48H (72) | 8'
49H (73) | 4'
4AH (74) | 2-2/3'
4BH (75) | 2'
4CH (76) | 1-3/5'
4DH (77) | 1-1/3'
4EH (78) | 1'
* The control value corresponds to the H.Bar levels as follows.
vv | H.Bar Level
————————-——+—————————————————————————————————
00H | 0
16H | 1
24H | 2
32H | 3
41H | 4
4FH | 5
5DH | 6
6AH | 7
7FH | 8
General Purpose Controller 5 (Controller number 80) (Rotary Speed)
[CTRL]
Status 2nd byte
BnH 50H
n =MIDI Channel Number:
vv =control value:
General Purpose Controller 6 (Controller number 81) (Rotary Brake)
[CTRL]
Status 2nd byte
BnH 51H
n =MIDI Channel Number:
vv =control value:
General Purpose Controller 7 (Controller number 82) (Reverb Return
Level) [CTRL]
Status 2nd byte
BnH 52H
n =MIDI Channel Number:
vv =control value:
General Purpose Controller 8 (Controller number 83) (Ring Modulator
Switch) [CTRL]
Status 2nd byte
BnH 53H
n =MIDI Channel Number:
vv =control value:
Effect 1 (Controller number 91) (Reverb Send Level) [EXT]
Status 2nd byte
BnH 5BH
n =MIDI Channel Number:
vv =control value:
Effect 3 (Controller number 93) (Chorus Send Level) [EXT]
Status 2nd byte
BnH 5DH
n =MIDI Channel Number:
vv =control value:
RPN MSB/LSB (Controller number 100, 101)
Status 2nd byte
BnH 65H
BnH 64H
n =MIDI Channel Number:
3rd byte
vvH
0H–FH (ch.1–ch.16)
00H–7FH (0–127) 0–63 = SLOW, 64–127 = FAST
3rd byte
vvH
0H–FH (ch.1–ch.16)
00H–7FH (0–127) 0–63 = SPIN, 64–127 =BRAKE
3rd byte
vvH
0H–FH (ch.1–ch.16)
00H–7FH (0–127)
3rd byte
vvH
0H–FH (ch.1–ch.16)
00H–7FH (0–127) 0–63 = OFF, 64–127 = ON
3rd byte
vvH
0H–FH (ch.1–ch.16)
00H–7FH (0–127)
3rd byte
vvH
0H–FH (ch.1–ch.16)
00H–7FH (0–127)
3rd byte
mmH
llH
0H–FH (ch.1–ch.16)
mm =upper byte (MSB) of parameter number specified by RPN
ll =lower byte (LSB) of parameter number specified by RPN
On the VK-77, RPN can be used to modify the following parameters.
RPN Data entry
MSB LSB MSB LSB
00H 00H mmH 00H
00H 01H mmH llH
* The value will be transmitted for the external upper/lower/pedal part that was designated by
External Part Fine Tuning parameter (REGISTRATION MIDI MENU -> Ext Fine Tune).
00H 02H mmH --
* The value will be transmitted for the external upper/lower/pedal part that was designated by
External Part Coarse Tuning parameter (REGISTRATION MIDI MENU -> Ext Coarse Tune).
7FH 7FH --- ---
Program Change [EXT] [ORCH] [CTRL]
Status 2nd byte
CnH ppH
n =MIDI Channel Number:
pp =Program number:
* The program number will be transmitted for the external upper/lower/pedal part that was desig-
nated by External Tone Select Upper/Lower/Pedal parameter (REGISTRATION MIDI MENU ->
Ext Tone Select U/L/P).
Channel Aftertouch [EXT] [ORCH]
Status 2nd byte
DnH vvH
n =MIDI Channel Number:
vv =Channel Aftertouch:
* Not transmitted for the external upper part when the External Upper Part Aftertouch (REGIS-
TRATION MIDI MENU ->ExtUpperAft Sw) is Off.
Pitch Bend Change [EXT] [ORCH]
Status 2nd byte
EnH llH
mm, ll = Pitch Bend value: 00 00H–40 00H–7F 7FH (-8192–0–+8191)
* Not transmitted for the external Upper/Lower/Pedal part, when the External Part Bender Switch
(REGISTRATION MIDI MENU -> Ext Bender) is Off.
System Common Message
Song Position
Status 2nd byte
F2H 00H
System Realtime Message
Active Sensing
Status
FEH
* This will be transmitted constantly at intervals of approximately 250 ms.
Continue
Status
FBH
Stop
Status
FCH
Explanation
Pitch Bend Sensitivity [EXT] [ORCH]
mm: 00H–18H (0–24 semitones)
ll: processed as 00H
specify up to 1 octaves in semitone steps.
Master Fine tuning [EXT]
mm, ll: 20 00H–40 00H–60 00H
(-8192 * 50 / 8192–0–+8192 * 50 / 8192 cent)
Master Coarse Tuning [EXT]
mm: 28H–40H–58H (-24–0–+24 semitones)
ll: Ignored (Processed as 00H)
RPN null [EXT] [ORCH]
Set Condition where RPN is unspecified.
0H–FH (ch.1–ch.16)
00H–7FH (prog.1–prog.128)
00H-3FH (Orchestral)
0H–FH (ch.1–ch.16)
00H–7FH (0–127)
3rd byte
mmH
3rd byte
00H
103