Roland VK-77 Manual Del Usuario página 100

* Data received from PEDAL KEYBOARD IN will be handled in the same way as the HOLD PEDAL
jack of the VK-77 itself.
Sound Controller 1–9 (Controller number 70–78) [ORGAN]
Status 2nd byte
BnH ccH
n =MIDI Channel Number:
cc =Controller number:
vv =control value:
* The Harmonic Bar level will change.
* The Value can be received when Harmonic Bar Mode (SYSTEM MIDI MENU -> Harmon-
icBarMode) is "Mode 2." To change the assignment of control changes to CC#1–31, 33–95, use
H.Bar Controller Number (SYSTEM MIDI MENU -> H.Bar CC No.)
* With the factory setting, control change message are assigned to each Harmonic Bar as follows.
cc | H.Bar Feet
———————————+—————————————————————————————————————
46H (70) | 16'
47H (71) | 5-1/3'
48H (72) | 8'
49H (73) | 4'
4AH (74) | 2-1/3'
4BH (75) | 2'
4CH (76) | 1-3/5'
4DH (77) | 1-1/3'
4EH (78) | 1'
* The control value corresponds to the H.Bar levels as follows.
vv | H.Bar Level
—————————————+—————————————————————————————————
00H–0EH | 0
0FH–1CH | 1
1DH–2AH | 2
2BH–38H | 3
39H–47H | 4
48H–55H | 5
56H–63H | 6
64H–71H | 7
72H–7FH | 8
General Purpose Controller 5 (Controller number 80) (Rotary Speed)
[CTRL]
Status 2nd byte
BnH 50H
n =MIDI Channel Number:
vv =control value:
General Purpose Controller 6 (Controller number 81) (Rotary Brake)
[CTRL]
Status 2nd byte
BnH 51H
n =MIDI Channel Number:
vv =control value:
General Purpose Controller 7 (Controller number 82) (Reverb Return
Level) [CTRL]
Status 2nd byte
BnH 52H
n =MIDI Channel Number:
vv =control value:
General Purpose Controller 8 (Controller number 83) (Ring Modulator
Switch) [CTRL]
Status 2nd byte
BnH 53H
n =MIDI Channel Number:
vv =control value:
100
3rd byte
vvH
0H–FH (ch.1–ch.16)
46H–4EH (70–78)
00H–7FH (0–127)
3rd byte
vvH
0H–FH (ch.1–ch.16)
00H–7FH (0–127) 0–63 = SLOW, 64–127 = FAST
3rd byte
vvH
0H–FH (ch.1–ch.16)
00H–7FH (0–127) 0–63 = BRAKE, 64–127 = SPIN
3rd byte
vvH
0H–FH (ch.1–ch.16)
00H–7FH (0–127)
3rd byte
vvH
0H–FH (ch.1–ch.16)
00H–7FH (0–127) 0–63 = OFF, 64–127 = ON
RPN MSB/LSB (Controller number 100,101)
Status 2nd byte
BnH 65H
BnH 64H
n =MIDI Channel Number:
mm =upper byte (MSB) of parameter number specified by RPN
ll =lower byte (LSB) of parameter number specified by RPN
The RPN (Registered Parameter Number) messages are expanded control changes, and each function
of RPN is described by the MIDI Standard.
To use these messages, you must first use RPN MSB and RPN LSB messages to specify the parameter
to be controlled, and then use Data Entry messages to specify the value of the specified parameter.
Once an RPN parameter has been specified, all Data Entry messages received on that channel will
modify the value of that parameter. To prevent accidents, it is recommended that you set RPN Null
(RPN Number = 7FH/7FH) when you have finished setting the value of the desired parameter.
On the VK-77, RPN can be used to modify the following parameters.
RPN Data entry
MSB LSB MSB LSB
00H 00H mmH 00H
* This messages can control the Organ Voice Pitch Bend Sensitivity parameter (ORGAN BASIC
MENU -> Org Bend Sens) when it is received in the channel which was specified by Control MIDI
Channel (SYSTEM MIDI MENU ->Control MIDI Ch).
* This messages can rewrite the Orchestral Voice Pitch Bend Sensitivity parameter (ORCHESTRAL
MENU -> Orch Bend Sens) when it is received in the channel which was specified by Orchestral
MIDI Channel (SYSTEM MIDI MENU ->Orch MIDI Ch).
00H 01H mmH llH
* This messages can control the Master Tune parameter (SYSTEM BASIC MENU -> Master Tune) of
the VK-77 itself when it is received in the channel which was specified by Control MIDI Channel
(SYSTEM MIDI MENU -> Control MIDI Ch).
7FH 7FH --- ---
Program Change [CTRL] [ORCH]
Status 2nd byte
CnH ppH
n =MIDI Channel Number:
pp =program number:
* This messages can control the registration when it is received in the channel which was specified
by Control MIDI Channel (SYSTEM MIDI MENU -> Control MIDI Ch).
* This messages can control each part of the program number of the orchestral voices when it is
received in the channel which was specified by Orchestral MIDI Channel (SYSTEM MIDI MENU -
> Orch MIDI Ch).
Channel Aftertouch [ORCH]
Status 2nd byte
DnH vvH
n =MIDI Channel Number:
vv =channel aftertouch:
Pitch Bend Change [CTRL] [ORCH]
Status 2nd byte
EnH llH
n =MIDI Channel Number:
mm, ll =Pitch Bend value:
* This messages can control Pitch Bend Change of the organ voice when it is received in the channel
which was specified by Control MIDI Channel (SYSTEM MIDI MENU -> Control MIDI Ch).
* This messages can control Pitch Bend Change of the each part of the orchestral voice upper/
lower/pedal when it is received in the channel which was specified by Orchestral MIDI Channel
(SYSTEM MIDI MENU -> Orch MIDI Ch).
3rd byte
mmH
llH
0H–FH (ch.1–ch.16)
Explanation
Pitch Bend Sensitivity [CTRL][ORCH]
mm: 00H–0CH (0–12 semitones)
ll: processed as 00H
specify up to 1 octaves in semitone steps.
Master Fine Tuning [CTRL]
mm, ll: 20 00H–40 00H–60 00H
(-8192 * 50 / 8192–0–+8192 * 50 / 8192 cent)
RPN null [CTRL][ORCH]
Set Condition where RPN is unspecified.
0H–FH (ch.1–ch.16)
00H–7FH (prog.1–prog.128)
0H–FH (ch.1–ch.16)
00H–7FH (0–127)
3rd byte
mmH
0H–FH (ch.1–ch.16)
00 00H–40 00H–7F 7FH (-8192–0–+8191)