Franklin Electric SUBMONITOR CONNECT Manual De Instalación Y Funcionamiento Del Propietario página 44

COMMUNICATIONS
Modbus RTU Communication
Mod
R/W RC Address Name
Bus
413 RW N Over Cur Level
414 RW N Over Cur Delay
415 RW N Over Cur Reset
416 RW N Over Cur Retry
417 RW N Over Cur Reset
Delay
418 RW N Unbl Cur Enable
419 RW N Unbl Cur Level
420 RW N Unbl Cur Delay
421 RW N Unbl Cur Reset
422 RW N Unbl Cur Retry
423 RW N Unbl Cur Rst Dly
424 RW N Grnd Flt Enable
425 RW N Grnd Flt Level
426 RW N No Cur Enable
427 RW N Unexp Cur Enable
428 RW N Out Cal Enable
429 RW N Max Str Enable
430 RW N Nominal Voltage
431
432 RW N Ovr Vlt Enable
433 RW N Ovr Vlt Level
434 RW N Ovr Vlt Delay
435 RW N Ovr Vlt Reset
436 RW N Ovr Vlt Retry
437 RW N Ovr Vlt Rst Dly
44
Choices/Range
100 to 200; default = 110
1 to 120; default = 30
0 - Manual
1 - Automatic (default)
1 to 10; default = 3
1 to 43,200; default = 900
0 - Off
1 - Fault and Alarm (default)
2 - Alarm Only
1 to 50; default = 5
1 to 120; default = 10
0 - Manual
1 - Automatic (default)
1 to 10; default = 3
1 to 43,200; default = 900
0 - Off
1 - Fault and Alarm (default)
2 - Alarm Only
1.0 to 10.0; default = 1.0
multi = 0.1
0 - Off (default)
1 - Fault and Alarm
2 - Alarm Only
0 - Off (default)
1 - Fault and Alarm (default)
2 - Alarm Only
0 - Off (default)
1 - Fault and Alarm (default)
2 - Alarm Only
0 - Off (default)
1 - Fault and Alarm (default)
2 - Alarm Only
120.0 to 72,000; default =
208.0 multi = 0.1
0 - Off
1 - Fault and Alarm (default)
2 - Alarm Only
101 to 125; default = 110
1 to 120; default = 10
0 - Manual
1 - Automatic (default)
1 to 10; default = 3
1 to 43,200; default = 900
Description
Over current level percentage. Percent of motor FLA/
SFA. If any phase current is greater than setting for Over
Current Delay, SMC faults/alarms.
Over current delay, in seconds, to trip fault/alarm. Timer
is reset if the current drops below the motor Over Current
Level.
Over current reset method
Over current automatic reset attempts
Over current automatic reset delay time
Current unbalance protection enable
Current unbalance level percentage
Current unbalance delay to trip fault/alarm in seconds
Current Unbalance Reset Method
Current unbalance automatic reset attempts
Current unbalance automatic reset delay in seconds
Ground Fault Protection Enable
Ground Fault Level in amperes
No Current Protection Enable
Unexpected Current Protection Enable
Out of Calibration Protection Enable
Maximum Start Time Protection Enable
Nominal Voltage setting
Overvoltage Protection Enable
Overvoltage Level Percentage
Overvoltage Delay Time in seconds
Overvoltage Reset Method
Overvoltage Automatic Reset Allowed Attempts
Overvoltage Automatic Reset Delay in seconds