Replacement Parts List - ROBBE Nano-Racer AT 6 Texan ARF Instrucciones De Montaje

Specification
Wingspan: approx. 715 mm
Overall length: approx. 555 mm
approx. 9.4 dm 2
Total surface area:
All-up weight: approx. 340 g
approx. 36.2 g/dm 2
Total surface area loading:
Dear Customer,
Congratulations on your choice of a factory-assembled model air-
craft from the robbe Modellsport range. Many thanks for placing
your trust in us.
The model can very quickly be completed ready to fly. Please read
right through these instructions and the separate information sheets
before attempting to assemble and fly the model, as this will make
it much easier to complete the tasks required.
We constantly strive to update our products to reflect the latest
developments. You can find out details of technical improve-
ments, updates and revised documention on the Internet by
calling up the appropriate product description at our website:
www.robbe.com.
All directions, such as "right-hand", are as seen from the tail of
the model, looking forward.
Notes on the power system
A brushless outrunner motor, propeller and spinner are factory-
installed.
The motor is connected to the speed controller, ready for use, and
the controller is correctly set up at the factory.
To complete the power system all you have to do is connect the
LiPo flight battery.
The radio control system
For this model you require a radio control system with at least four
channels. We particularly recommend 2.4 GHz systems.
The receiving system is powered by the speed controller's integral
BEC system.
Before you check the model's working systems, set the control
surfaces to neutral from the transmitter (transmitter sticks and trims
central).
© robbe Modellsport
Assembly and operating instructions
AT 6 Texan ARF
Before operating the model always move the throttle stick to the
"motor stopped" position before switching the transmitter on. Only
then connect the flight battery.
To switch off, first disconnect the flight pack from the speed control-
ler, and only then switch the transmitter off.
When installing or setting up the receiving system componen-
ts, including the speed controller, be sure to read and observe
the instructions supplied with them.
Read right through the safety notes for the LiPo battery
(page 4), and the instructions supplied with the battery
charger, before using these items for the first time.
Joining the components, recommended adhesives
All parts must be trial-fitted "dry" (without glue) before you
reach for the glue.
robbe Speed Extra No. 5061
Activator spray No. 5020
Please take great care to avoid excess adhesive or activator run-
ning onto the painted surfaces, as this will damage the finish.
Recommended accessories
Description Order No.
FF-6 R617
2.4 GHz radio control system F 4069
Battery charger, e.g.
Power Peak® A4 EQ-LCD 8560 or
Power Peak® B6-EQ-BID 8561
Battery charge lead, CT-2 8254
Velcro (hook-and-loop) tape 1713
Kit contents
Fuselage, complete with motor, speed controller and servo.
Integral wing panels with L.H. / R.H. ailerons and servos
Tailplane and elevator
Fin
Factory-fitted propeller and spinner
2 x Aileron pushrod, one Z-bend
1 x Elevator pushrod, one Z-bend
2
1 x Y-lead
3 x Control surface horn
1 x 3S1P LiPo battery, 850 mAh, 20 C

Replacement parts list

Order No. Description
F 1291 S3107 Nano servo
25360002 BL speed controller
4952 Roxxy 2826/09 BL outrunner motor
25360004 3S1P LiPo battery, 850 mAh, 20C
4794 Propeller driver
25220001 Cowl Texan
25200002 5.5 x 4.5" propeller + spinner 38 D
4077 CT-2 plugs / sockets
Figs. 1 and 2
- Opening and closing the canopy:
The canopy is retained by the cowl at the front, and by a tongue
at the rear.
- To open the canopy, slide it forward, raise it at the rear and lift it
off.
- Reverse the procedure to replace the canopy.
Fig. 3
- Lightly sand the joint areas of the fin, and the surfaces inside the
fuselage recess.
Fig. 4
- Glue the fin in place with cyano.
Fig. 5
- Check that the fin is exactly at right-angles to the tailplane.
Fig. 6
- Apply a strip of Velcro tape to the underside of the flight battery.
Stick the mating piece inside the fuselage.
No.
2522