Making Coffee - melitta LOOK Therm Timer Manual De Instrucciones

The appliance is pre-set for a high level of water
hardness (level 4). You can find out the level of water
hardness in your area by asking your local water
provider or by using water hardness measuring strips
available in the shops. For softer water the descaling
display can be adjusted to descale less often.
• Hold down the CALC-button  and by briefly
pressing the "m"-button  set the desired level of
water hardness. The hardness setting will then
show in the display.
• Once you have set the desired level of water
hardness, let go of the CALC-button.
Your settings are now saved.
• The settings and display are shown in the table.
hardness
I
setting
<7°
°dh
dh
1
Display 
Please note:
• Water hardness cannot be programmed while brewing.
• The last water hardness level chosen remains even
after removing the power cable.

4. Making coffee

• Ensure that the appliance is connected to
the power source.
• Fill the water tank.
• Remove the detachable water tank by holding the
recessed grip and pulling straight up .
• Remove the water tank lid and fill with the desired
amount of fresh water from the tap. Using the water
level indicator on the tank you an choose the correct
number of cups.
• Close the tank by replacing the lid and insert the
tank back in the appliance. Please ensure that you
replace the tank upright in the appliance. The guide
rails on the appliance (left of the tank) will help you
with this .
• Alternatively use the therm jug to pour the water
into the tank in the appliance . The required
amount of water can be seen on the water level
indicator on the tank.
Small cup symbol = approx. 85 ml coffee per cup,
large cup symbol = approx. 125 ml coffee per cup
• Close the lid on the water tank and place the therm
jug with closed lid in the appliance.
• Open the swing filter  to the left.
filter bag 1x4
• Fold a Melitta
®
and place it in the filter holder . Press the filter bag
into the filter holder by hand, to ensure a good fit.
• Put the ground coffee into the coffee filter. We
recommend using 6 g of coffee per large cup at a
medium setting of the AromaSelector
• Alternatively, you can vary the taste of the coffee
according to your personal preference using the
same quantity of coffee. For a milder coffee, turn the
AromaSelector  to the left (
®
coffee, turn it to the right (
• Swing the filter back into the appliance. An audible
II III IV
14-21°
7-14° >21°
dh dh dh
2 3 4
at the embossed seam
®
.
®
). For a stronger
).
click tells you it is inserted properly.
• The appliance turns off automatically short after
brewing. This avoids unnecessary use of electricity
and saves energy. You can of course turn the machine
off manually at any time.
• The drip stop prevents your coffee from dripping
when you remove the pot from the appliance .
• With the help of the detachable inner filter you can
dispose of the filter bag simply and easily.
5. Using the therm jug
• The brewed coffee flows through the central valve in
the insulated lid of the jug.
• To pour coffee press down on the sealing lever .
• Remove the lid simply by pressing the seals on the
side while lifting the lid up .
6. Timer Feature
The appliance is equipped with a TImer feature. This
starts the brewing process at a time you programme.
• Prepare the appliance as described in point 4 'making
coffee', but without pressing the STArT button.
• To set the desired start time, hold down the TIMER
button . The first time you programme it the
display will show 00:00.
• Set the desired start time by repeatedly pressing the
"h" and "m" buttons . This goes faster if you hold
down the button.
• After letting go of the TIMER button the current
time will show. The chosen start time is saved until
you set a different time or remove the appliance
from the power source.
• By briefly pressing the TIMER button  the timer
feature is activated for the next brewing process.
To show this the TImer button  is illuminated
and the programmed start time shows briefly in the
display .
• The appliance automatically starts to make coffee at
the time you have set.
• As long as you do not remove the plug from the
socket or set a new start time, the previous start
time is saved.
• By briefly pressing the TIMER button  you can
deactivate the timer feature at any time. The light in
the TImer button  goes off.
• If you want to make coffee before the start time you
have programmed, press the STArT button . The
TImer feature will be deactivated.
7. Cleaning and maintenance
External cleaning
• Switch off the machine before cleaning and disconnect
the power cable.
• Allow the appliance to cool completely before
cleaning it.
• Clean the parts that come into contact with coffee
(jug, filter holder, etc.) after each use.
• The housing can be cleaned with a soft damp cloth.
• The jug lid, the filter insert and the swing filter 
can be washed in the dishwasher.
• Do not use harsh or abrasive cleaning agents.
Descaling
The CALC button  lights up again if the appliance
has been turned off without descaling. The CALC
button  will go off again only after the descaling
GB
9