Troubleshooting - WAGNER CONTROL PRO 190 Manual Del Propietário

TROUBLESHOOTING

PROBLEM
A. The sprayer does not turn on.
B. The sprayer starts but does not
draw material when the PRIME/
SPRAY knob is set to PRIME
C. The sprayer draws up material
but the pressure drops when
the gun is triggered (bad spray
pattern or no spray pattern)
D. The PRIME/SPRAY knob is set to
SPRAY and there is flow through
the material return tube
E. The spray gun leaks
F. The spray tip assembly leaks
G. The spray gun will not spray
H. The spray pattern is poor (tailing)
I. The spray tip will not turn
CAUSE
1. The sprayer is not plugged in.
2. Pressure control knob is set to OFF.
3. The sprayer shuts off while under pressure.
4. No power is coming from power outlet.
5. The extension cord is damaged or is not the
proper gauge or length.
6. There is a problem with sprayer motor.
7. Spray tip clogged.
1. The inlet valve is stuck from old material.
2. There is no suction at the inlet valve.
3. The suction tube is not properly installed.
4. The suction tube is damaged or completely
clogged.
5. The inlet filter is clogged.
6. The outlet valve is stuck or contains debris.
7. The inlet valve or outlet valve is worn or
damaged.
8. The PRIME/SPRAY valve is plugged.
1. Pressure too low.
2. The spray tip is worn.
3. The inlet filter is clogged.
4. The spray tip is plugged.
5. The spray gun filter is clogged.
6. The material is too heavy or thick.
7. The material is too coarse.
8. The outlet valve assembly is damaged or worn.
9. Spray hose is too long.
1 0. Filter accessory is dirty or plugged.
1. The PRIME/SPRAY valve is dirty or worn.
1. Internal parts of spray gun are worn or dirty.
1. The tip guard nut is loose.
2. Tip guard was assembled incorrectly.
3. Tip seal is worn
1. The spray tip plugged.
2. The spray tip is in wrong position.
3. PRIME/SPRAY knob not set on SPRAY.
4. Filter accessory is dirty or plugged.
1. Pressure too low.
2. The spray tip is plugged.
3. The inlet filter is clogged.
4. The spray gun filter is clogged.
5. The spray tip is worn.
6. The material is too heavy or thick.
7. Spray hose is too long.
1. High pressure has locked the spray tip in place.
SOLUTION
1. Plug the sprayer in.
2. Turn pressure control knob to recommended setting.
3. Motor will cycle ON and OFF while spraying to
regulate pressure. This is normal.
4. Reset circuit breaker or find another outlet.
5. Refer to General Information.
6. Contact customer service (customerservice@wagner-
group.com).
7. Refer to Clear the Spray Tip.
1. Push pusher stem to release. If still stuck refer to
Cleaning the Inlet Valve.
2. Remove suction tube and check suction by placing
finger on bottom of inlet valve. If no suction, refer to
Cleaning the Inlet Valve.
3. Reinstall the suction tube
4. Replace with a new suction tube.
5. Refer to Clean the Inlet filter or replace the inlet filter.
6. Refer to Cleaning the Outlet Valve. Or perform steps
2-4 in Long Term Storage using water instead of oil.
7. Replace the inlet valve or outlet valve.
8. Contact customer service (customerservice@wagner-
group.com).
1. Increase the pressure by turning the pressure control
knob to a higher setting.
2. Replace spray tip with a new one.
3. Refer to Clean the Inlet filter, or replace with a new
inlet filter.
4. Refer to Clear the Spray Tip or replace with a new
spray tip.
5. Refer to Clean the Spray Gun Filter. Keep extra filters
on hand
6. Thin the material, or use a larger tip (see Tip Selection
Chart, page 13).
7. Strain the material or purchase the filter accessory
(see Accessories, page 78).
8. Replace the outlet valve.
9. Remove any extra hose length that has been added.
10. Clean or replace.
1. Contact customer service (customerservice@wagner-
group.com).
1. Contact customer service (customerservice@wagner-
group.com).
1. Tighten tip guard nut.
2. Remove and assemble correctly.
3. Replace tip seal
1. Refer to Clear the Spray Tip .
2. Rotate spray tip to SPRAY position.
3. Turn PRIME/SPRAY knob to SPRAY.
4. Clean or replace.
1. Increase the pressure by turning the pressure control
knob to a higher setting.
2. Refer to Clear the Spray Tip
3. Refer to Clean the Inlet filter or replace with a new
inlet filter.
4. Refer to Clean the Spray Gun Filter. Keep extra filters
on hand
5. Replace the spray tip.
6. Thin material per manufacturer's recommendations.
7. Remove any extra hose length that has been added.
1. Refer to Clear the Spray Tip.
EN
25