Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

EXTEnSIOn COrDS

grounded tools require a three wire extension cord
As the distance from the power supply outlet increases, you must use a heavier gauge extension cord. using extension cords with inadequately sized
wire causes a serious drop in voltage, resulting in loss of power and possible tool damage. Refer to the table shown below to determine the required
minimum wire size.
The smaller the gauge number of the wire, the greater the capacity of the cord. For example: a 14-gauge cord can carry a higher current than a 16-
gauge cord. When using more than one extension cord to make up the total length, be sure each cord contains at least the minimum wire size required.
If you are using one extension cord for more than one tool, add the nameplate amperes and use the sum to determine the required minimum wire size.
guidelines for Using Extension Cords
• If you are using an extension cord outdoors, be sure it is marked with the suffix "W-A" ("W" in Canada) to indicate that it is acceptable for outdoor use.
• Be sure your extension cord is properly wired and in good electrical condition. Always replace a damaged extension cord or have it repaired by a
qualified person before using it.
• Protect your extension cords from sharp objects, excessive heat, and damp or wet areas.
Recommended Minimum Wire Gauge for Extension Cords (120 Volt)
Nameplate
Extension Cord Length
Amperes
25 Feet
(At Full Load)
0–2.0
18
2.1–3.4
18
3.5–5.0
18
5.1–7.0
18
7.1–12.0
18
12.1–16.0
14
16.1–20.0
12
SPECIFIC SAFETY rULES FOr MULTI-PUrPOSE OSCILLATIng TOOLS
WArnIng:
DO nOT LET COMFOrT Or FAMILIArITY WITH PrODUCT (gAInED FrOM rEPEATED USE)
rEPLACE STrICT ADHErEnCE TO PrODUCT SAFETY rULES. If you use this tool unsafely or incorrectly, you can
suffer serious personal injury!
WArnIng:
Hold tool by insulated gripping surfaces when performing an operation where cutting tools may
contact hidden wiring or its own cord. Contact with a "live" wire will make exposed metal parts of the tool "live" and
shock the operator!
• Always wear safety glasses or goggles.
• Hold the Oscillating Tool by its insulated gripping surfaces to avoid electrical shock from unseen
"live" wires.
• Always hold the tool firmly. DO not
• Check your work area for proper clearances before cutting.
• DO not cut nails or screws
• Before switching on the tool,
• Do not use tool if switch does not turn it on or off.
must be repaired.
• Wear cushioned protective gloves to minimize the vibration.
• Do not wet-sand with this tool.
injury.
• Always be sure that the tool is switched off and unplugged before adjusting,
.
a function on the tool
. Double insulated tools can use either a two or three wire extension cord.
50 Feet
75 Feet
18
18
18
18
18
16
16
14
14
12
12
10
10
8
Normal prescription eye or sunglasses are not safety glasses.
leave the tool running unless hand held.
unless you are using a blade specifically designed for this purpose. Inspect your material before cutting
be sure the blade is not contacting the work piece.
Any tool which can not be controlled by the switch is dangerous and
Water or moisture entering the motor housing can cause electric shock and serious personal
100 Feet
150 Feet
18
16
16
14
14
12
12
12
10
8
10
8
8
6
This will avoid cutting into your workbench, the floor, etc.
Excessive vibration may cause personal injury.
adding accessories, or checking
200 Feet
16
14
12
10
8
6
6
.
5

Publicidad

Tabla de contenido
loading

Tabla de contenido