Explanation Of General View - stayer PR6 Manual De Instrucciones

1 Loosen
2 Tighten
3 Hold
4 Base
5 Adjusting roller
6 Bit protrusion
7 Lever
8 Scale
9 Switch lever
10 Workpiece
11 Feed direction
12 Bit revolving direction
13 View from the top of the tool
*Accessories shown or described are not part of the standard delivery scope of the product. A complete overview of
accessories can be found in our accessories program.
PR6
Power input
No load speed
Collet
Routing depth
Weight
These data are valid for nominal voltages of [U] 230/240 V ~ 50/60 Hz – 110/120
V ~ 60 Hz. These values may change of the voltage was lower and in the specific
embodiments for certain countries.
• Due to the continuing program of research and
development, the specifications herein are subject to
change without prior notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for flush trimming and profiling of
wood, plastic and similar materials.
Power supply
The tool should be connected only to a power supply of the
same voltage as indicated on the nameplate, and can only
be operated on single-phase AC supply. They are double-
insulated in accordance with European Standard and can,
therefore, also be used from sockets without earth wire.
Safety hints
For your own safety, please refer to enclosed safety
instructions.
ADDITIONAL SAFETY RULES
1. Hold tool by insulated gripping surfaces when
performing an operation where the cutting tool may
contact hidden wiring or its own cord. Contact with a "live"
wire will make exposed metal parts of the tool "live" and
shock the operator.
2. Wear hearing protection during extended period
of operation.
3. Handle the bits very carefully.
4. Check the bit carefully for cracks or damage
before operation.
Replace cracked or damaged bit immediately.
5. Avoid cutting nails. Inspect for and remove all
ENGLISH
11

Explanation of general view

14 Correct bit feed direction
15 Trimmer shoe, straight guide or
trimmer guide
16 Bolt
17 Guide plate
18 Straight guide
19 Flat washer*
20 Wave washer*
21 Wing nut
22 Clamp screw (A)
23 Centre hole
24 Nail
25 Adjusting screw
W 550
min 32.000
-1
mm 6
mm 0-40
Kg 1.8
11
26 Clamp screw (B)
27 Trimmer guide
28 Bit
29 Guide roller
30 Screwdriver
31 Base protector
32 Screws
33 Straight bit
34 Templet
35 Distance (X)
36 Templet guide 10
37 Limit mark
38 Brush holder cap
nails from the workpiece before operation.
6. Hold the tool firmly.
7. Keep hands away from rotating parts.
8. Make sure the bit is not contacting the workpiece
before the switch is turned on.
9. Before using the tool on an actual workpiece, let it
run for a while.
Watch for vibration or wobbling that could indicate
improperly installed bit.
10. Be careful of the bit rotating direction and the feed
direction.
11. Do not leave the tool running. Operate the tool
only when hand-held.
12. Always switch off and wait for the bit to come to a
complete stop before removing the tool from workpiece.
13. Do not touch the bit immediately after operation; it
may be extremely hot and could burn your skin.
14. Always lead the power supply cord away from the
tool towards the rear.
15. Do not smear the tool base carelessly with thinner,
gasoline, oil or the like.
They may cause cracks in the tool base.
16. Draw attention to the need to use cutters of the
correct shank diameter and which are suitable for the
speed of the tool.
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Installing or removing trimmer bit (Fig. 1)
Important:
Always be sure that the tool is switched off and unplugged
before installing or removing the bit.
Insert the bit all the way into the collet cone and tighten the
collet nut securely with the two wrenches. To remove the
bit, follow the installation procedure in reverse.
CAUTION:
• Do not tighten the collet nut without inserting a bit,
or the collet cone will break.
• Use only the wrenches provided with the tool.