Speaker And Delay/Distance Setup; Miscellaneous Settings; System Setup - Rotel RAP-1580MKII Manual De Instrucciones

deciding how loud to playback movie soundtracks and adjust the master
volume control accordingly. Regardless of your listening levels, using an SPL
meter to calibrate equal levels for all speakers in the system is recommended.

Speaker and Delay/Distance Setup

SPEAKER DISTANCE SETUP
FRONT LEFT : 10.00 FT 3.05M
FRONT RIGHT : 10.00 FT 3.05M
SURROUND RIGHT : 10.00 FT 3.05M
CENTER BACK RIGHT : 10.00 FT 3.05M
CEILING FRONT RIGHT : 10.00 FT 3.05M
CEILING REAR RIGHT : 10.00 FT 3.05M
CEILING REAR LEFT : 10.00 FT 3.05M
CEILING FRONT LEFT : 10.00 FT 3.05M
CENTER BACK LEFT : 10.00 FT 3.05M
SURROUND LEFT : 10.00 FT 3.05M
SUBWOOFER : 10.00 FT 3.05M
The SPEAKER DISTANCE SETUP menu, which is reached from the MAIN
menu, allows you to set the delay for individual speakers. This ensures that
the sound from each speaker arrives simultaneously at the listening position,
even when the speakers are not all placed at equal distances from the
listener. Increase the delay to speakers located closer to the seating area
and decrease the delay to speakers located farther from the seating area.
The Audio Configuration will determine which speakers are displayed in
the Speaker Distance Setup menu.
This Rotel processor makes setting the delay time for each speaker very
easy. Simply measure the distance (in feet or meters) from your seating
position to each speaker in your system. Set the measured distance in the
line for each speaker. The menu provides a line for each speaker configured
in your system and gives a range of settings up to 33 feet (10.6 meters)
in 0.25 foot (0.075 m) increments with each increment equivalent to an
additional delay of 0.25 ms.
To change a setting, place the highlight on the desired line using the Up/
Down arrow buttons and use the Left/Right arrow buttons to increase or
decrease the delay. To return to the MAIN menu, press the BACK button or
select "BACK" on the OSD. Press the SETUP/MENU button or select "EXIT"
on the OSD to exit setup and return to normal operation.

Miscellaneous Settings

System Setup

LANGUAGE : English
IR REMOTE CODESET : Codeset 1
DISPLAY : HDMI and TFT
TFT BRIGHTNESS : 0
NETWORK WAKEUP : Disable
NETWORK CONFIGURATION
SOFTWARE INFORMATION
RESTORE FACTORY DEFAULT
This SYSTEM SETUP menu, reached from the MAIN menu, provides access
to several miscellaneous settings as follows:
LANGUAGE: Selects a language for the On Screen Display.
NOTE: The OSD ONLY contains English, French, German, Spanish
and Italian.
CENTER : 10.00 FT 3.05M
BACK
SYSTEM SETUP
POWER OPTION
BACK
IR REMOTE CODESET: The RAP-1580MKII has two IR codesets and can be
changed in the event there is a conflict of IR codes with other Rotel products.
NOTE: After changing the IR REMOTE CODESET the remote must
also be changed to continue using the remote control. Push and hold
the TUNER button and 1 (or TUNER and 2 for codeset 2) at the same
time and hold for approximately 5 seconds until the backlights on the
remote control blink on then off then release both buttons. This sets the
remote control to use codeset 1 (or codeset 2 if TUNER and 2 are held).
DISPLAY: Sets the information shown on the main HDMI OSD and front TFT
display. Settings are "Off", "HDMI Only", "TFT Only" or "HDMI And TFT".
TFT BRIGHTNESS: Sets the brightness of the front TFT display. Settings range
from -10 to +10.
NETWORK WAKEUP: Enables or Disables power on and power off via the
network connection. Enable this function for use with automation systems
using IP control.
NOTE: When Network Wakeup is configured to enabled, the RAP- 1580MKII
will consume additional power in standby mode.
POWER OPTION: Access to configuration of Auto Power Down Timer, Max
Power On Volume, Power Mode and Signal Sense Input.
POWER OPTION
AUTO POWER DOWN TIMER : Disable
MAX POWER ON VOLUME : 45
POWER MODE : Normal
SIGNAL SENSE INPUT : Disable
AUTO POWER DOWN TIMER: Sets the amount of time the units stays
powered on when there is no audio signal. The RAP-1580MKII will
automatically go to standby mode if audio is not detected for the
specified timer period. "DISABLE" is the factory default.
Valid settings include: DISABLE, 1 Hour, 2 Hours, 4 Hours.
NOTE: Some regions require the AUTOMATIC POWER OFF timer
default setting to be 20 minutes. This can be changed in the SETUP
MENU to any of the available options. For questions about the Automatic
Power Off settings please contact your authorized Rotel dealer.
NOTE: Some products cannot detect ANALOG signal inputs and
the unit may power off if there is no digital audio source detected or
user action with the remote control or front panel. Analog input signal
detection is not available in all models which may cause the unit to
inadvertently power off. In this case the Automatic Power Off timer
should be set to DISABLED.
MAX POWER ON VOLUME: Specifies a maximum volume level to be
used each time the unit powered on, between 20 dB to 70 dB, in 1
dB increments.
BACK
27